Search Results

The paper describes how laser light sheet illumination was used to study the onset and development of cavitation in a scaled up plain orifice nozzle. In addition, measurements were taken using laser Doppler velocimetry and the refractive index matching technique, and these establish the velocity profiles within the orifice under non-cavitating conditions. The light sheet makes visible new detail in the cavitating flow field and additional stages in the cavitation process are identified. The mechanism which causes hydraulic flip is demonstrated and confirms the authors' hypothesis from previous studies. An investigation into the form which the cavitation takes is included: flow conditions are demonstrated in which the cavitation produces an opaque mass of small bubbles, and alternative conditions in which large transparent vapour pockets are produced.

An experimental study was made to investigate the effect of combustion chamber configuration, top clearance, nominal swirl ratio, and spark plug position on in-cylinder combustion in a spark-ignited natural gas engine, which is converted from a direct injection diesel engine. Flame propagation in a single-cylinder visualization engine was measured from the cylinder axis direction by the high speed schlieren method, over the wide range of combustion chamber configuration, top clearance, nominal swirl ratio, and spark plug position. The results showed that flame does not propagate concentrically to the spark plug, but is shifted by swirl, which is the main flow in this engine. Smaller piston cavity diameter led to more rapid flame propagation, resulting in larger heat release rate and larger cylinder pressure. Piston cavity diameter does not affect the initial combustion until TDC.

The interaction of fuel sprays and airflow in the intake system of a port fuel-injected spark-ignition engine has been examined experimentally in a pulsating-flow rig which comprised the cylinder head and intake manifold of a production engine connected to a large-capacity plenum chamber, with the camshaft of the intake valves driven by an electrical motor at engine speeds between 1000 and 5000 rpm and with air sucked through the system by a suction fan. Static pressure measurements in the intake port showed periodic pulsations with frequencies of 360 and 200 Hz with open and closed valves, respectively, and these corresponded to quarter- and half-waves in the manifold and were independent of engine speed.

Experiments have been conducted in a firing single-cylinder spark-ignition engine employing a Ford Zetec cylinder head that has been modified to operate with either standard port-fuel-injection, air-forced port-fuel-injection or direct-injection. The engine utilizes a fused silica cylinder and therefore provides extensive optical access to the combustion chamber. Tests were conducted using a constant speed simulated cold start procedure, which is composed of an initial start-up transient and a quasi-steady-state idle period. In this procedure, the engine is briefly motored at 889 rpm and then combustion commences shortly after the start of fuel injection. Measurements which were performed include in-cylinder pressure as well as intake valve, exhaust valve, piston, cylinder, head, and intake air temperature throughout each cycle of the test period. The engine-out total hydrocarbon emissions were also measured.

A thermodynamic methodology of TDC determination in IC engines based on a motoring pressure-time diagram is presented. This method consists in entropy calculation and temperature-entropy diagram analysis. When the TDC position is well calibrated, compression and expansion strokes under motoring conditions are symmetrical with respect to the peak temperature in the (T,S) diagram. Moreover, in case of error on the TDC position, a loop appears, which has no thermodynamic significance. Hence, an easy methodology has been conceived to obtain the actual position of TDC. This methodology is applied to motoring measurements in order to present its performance, which are compared to usual methods.

The effects of the cetane improvers* 2-ethylhexyl nitrate (EHN) and di-tertiary-butyl peroxide (DTBP) on regulated exhaust emissions from a 1993 Detroit Diesel Series 60 heavy-duty diesel engine were studied. EHN and DTBP were added to two commercially available fuels at concentrations ranging from 500 to 12,000 ppm by volume. Both additives reduced CO, NOx, and particulate emissions as measured in the hot start portion of the FTP heavy-duty transient emissions cycle. A comparison of the emissions response of the two additives shows that the nitrogen in EHN does not contribute to NOx emissions at typical treat rates.

During the last 10 years many researchers and technical groups have studied and performed tests in the area of diesel fuel lubricity [1]1. Protection of diesel engine fuel delivery system components from excessive wear has been the major mission of these efforts. Understanding of the issue, developing laboratory test methods, specifying appropriate fuel properties, and creating mechanical modifications to the equipment, as well as adding lubricity additives to the fuels, describes the bulk of the work which has been performed in this area. Technical groups from several organizations such as the Society of Automotive Engineers (SAE), the Coordinating European Council (CEC), and the International Organization for Standardization (ISO) have made substantial progress and some have come up with test methods and fuel specifications [2].

Experiments were performed in an optically-accessible DI Diesel engine to investigate the effects of the addition of oxygenated blending compounds to Diesel fuel. The focus of the study was to determine how the structure and boiling point of the oxygenating compounds affect the emissions of NOx and soot. NOx, CO2 and CO concentrations in the engine exhaust were measured using gas analyzers. Laser light extinction was used to measure time-resolved, in-cylinder soot concentrations. Two different oxygenate families, maleates and glycol ethers, were chosen to study the effects of molecular structure on emissions. For both families, oxygenates of various boiling points were examined within the distillation range of the base Diesel fuel. All oxygenates were blended into the base Diesel fuel to obtain two percent oxygen by mass.

I The effect of Cetane Number (CN) of the fuel and the addition of cetane improvers on the cold starting and white smoke emissions of a diesel engine was investigated. Tests were conducted on a single-cylinder, four-stroke-cycle, air-cooled, direct-injection, stand-alone diesel engine in a cold room at ambient temperatures ranging from 25 °C to - 5 °C. Five fuels were used. The base fuel has a CN of 49.2. The CN of the base fuel was lowered to 38.7 and 30.8 by adding different amounts of aromatic hydrocarbons. Iso-octyl nitrate is added to the high aromatic fuels in order to increase their CN to 48.6 and 38.9 respectively. Comparisons are made between the five fuels to determine the effect of CN and the additive on cylinder peak pressure, heat release rate, cold start-ability, combustion instability, hydrocarbon emissions and solid and liquid particulates.

Comparing with the previous Auto/Oil programs, the total plan and current status of the air quality modeling study in JCAP are presented. The total plan of air quality modeling study has the following characteristics: 1) Vehicle emission inventory program is developed by considering the original features of Japan. 2) Not only the urban air quality but also the road sides pollutants dispersion is evaluated. 3) The chemical reaction model for the secondary particulate formations is developed on the basis of the smog chamber experiments. 4) For the cost-effectiveness analysis of vehicle/fuel technologies, the output of the air quality modeling will be combined with the cost data of new vehicle emission reduction technologies As the first step, preliminary modeling studies are conducted to understand the overall tendency of the air quality change toward 2010 in Tokyo urban area.

Variations in air-fuel ratio within a 16-valve port-injection spark-ignition engine have been examined as a consequence of rapid transients in load at constant speed with fuel injection controlled by the production engine-management system and by a custom-built controller. The purpose was to minimize excursions from stoichiometry by the use of a controller to impose an injection strategy, guided by results obtained with the production management system. The strategy involves a model that takes account of manifold filling and the delays in transport of fuel from the injectors to the cylinder. The results show that the excursions in air-fuel ratio from stoichiometry were reduced from more than 25% to 6%.

Six commercial different additive packages to be used in the Venezuelan Internal Market Diesel formulations were evaluated in terms of their performance in corrosion inhibition, oxidation stability, injector cleanliness and emissions, as well as fuel economy improvement. Laboratory, field and bench tests were carried out. In laboratory tests, additives evaluated were added to four Venezuelan Diesel fuel formulations at the recommended supplier doses: corrosion (ASTM D665), oxidation stability (ASTM D2274), emulsification (ASTM D1094). Also, physicochemical properties required by Venezuelan Diesel fuel specifications were evaluated. Three different trucks (per additive) were run in fleet tests in order to determine injector cleanliness performance. Truck injector flow was measured in every injector, according to ISO 4010 procedure, before and after 5000-6000 km field accumulations. Two trucks were run without additive dosification, and were used for base line comparison.

In spite of the efforts of related industries, the air pollution situation particularly in urban areas of Japan is not satisfactory. It has been shown that air pollution is caused mainly by increased automotive traffic and increased penetration of diesel vehicles. Air-quality problems will become much more complicated and more severe in the future with increased emphasis on reducing air pollution and global warming. These situation will require continuous reduction of automobile emissions. In order to obtain cleaner exhaust emissions, cooperative studies between vehicle and fuel technologies are considered to be essential, and AQIRP in the United States and Auto/oil Program in Europe were already conducted to develop the best combination of measures for air pollution improvement. In 1996, Japan Clean Air Program (JCAP) was launched by Petroleum Energy Center (PEC) in cooperation with the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association (JAMA).

Emissions of six 32 passenger transit buses were characterized using one of the West Virginia University (WVU) Transportable Heavy Duty Emissions Testing Laboratories, and the fixed base chassis dynamometer at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Three of the buses were powered with 1997 ISB 5.9 liter Cummins diesel engines, and three were powered with the 1997 5.9 liter Cummins natural gas (NG) counterpart. The NG engines were LEV certified. Objectives were to contrast the emissions performance of the diesel and NG units, and to compare results from the two laboratories. Both laboratories found that oxides of nitrogen and particulate matter (PM) emissions were substantially lower for the natural gas buses than for the diesel buses. It was observed that by varying the rapidity of pedal movement during accelerations in the Central Business District cycle (CBD), CO and PM emissions from the diesel buses could be varied by a factor of three or more.

Many efforts have been made to apply the diesel exhaust particulate after-treatment system in practical use during the past ten years. In this paper, a diesel exhaust particulate after-treatment system with microwave energy as its external regeneration energy source is described, and the microwave regeneration characteristics of the diesel exhaust particulate after-treatment system developed are studied. The experimental results show that the regeneration efficiency can reach up to 80% with a wide regeneration window and a suitable regeneration duration. The effect of air supply on filter regeneration is also observed. It is proven that the microwave regeneration technique employed in the system is simple, effective and reliable.

Speed-time and video data were logged for tractor-trailers performing local deliveries in Akron, OH. and Richmond, VA. in order to develop an emissions test schedule that represented real truck use. The data bank developed using these logging techniques was used to create a Yard cycle, a Freeway cycle and a City-Suburban cycle by the concatenation of microtrips. The City-Suburban driving cycle was converted to a driving route, in which the truck under test would perform at maximum acceleration during certain portions of the test schedule. This new route was used to characterize the emissions of a 1982 Ford tractor with a Cummins 14 liter, 350 hp engine and a 1998 International tractor with a Cummins 14 liter, 435 hp engine. Emissions levels were found to be repeatable with one driver and the driver-to-driver variation of NOx was under 4%, although the driver-to-driver variations of CO and PM were higher.

A methodology has been developed to enable a single, gaseous sample to be collected from the diluted exhaust stream of heavy duty diesel engines operating over the European 13 mode ECE R49 emission cycle. The sample consists of timed contributions of dilute exhaust gas from each mode (weighted appropriately) to provide a gas sample that is representative of the complete cycle. The sample is collected in a Tedlar bag prior to GC analysis for individual hydrocarbon speciation. This methodology has also been extended to allow for the collection of a representative carbonyl sample using 2,4-dinitrophenyl-hydrazine (2,4-DNPH) impregnated cartridges. Results obtained from these systems are reported and compared to results obtained from light duty (diesel and gasoline) investigations.

Several candidate oxygenates have been proposed for use with diesel fuel. This paper examines the safety and health issues associated with the use of these oxygenates. The primary fire safety hazard associated with the use of oxygenates is increased diesel fuel volatility and consequent low flash point. Peroxide formation may be a hazard for some oxygenates, but no quantitative information on the extent of the hazard was located for any of the candidate oxygenates. Little information is available on inhalation, ingestion, or skin exposure toxicity hazards. Of the candidate ethers, only pentyl ether, 2-ethoxyethyl ether (diethyl carbitol), and dibutoxymethane (butylal) do not have low flash points or significant known toxicity problems.

This work includes an assessment of the lubricity of Greek road diesel fuel of low sulfur content, and the effect of the addition of two different types of biodiesel which can be produced from raw materials abundant in the Mediterranean area. In this study, a series of representative fuels of the Greek fuel market were tested. In some of them, the lubricity was measured three times, during a period of three months from the day of each sample was produced. In all cases a decrease of the wear scar diameter (WSD) was measured; this behaviour could be attributed to the oxidation reactions that take place during the storage period. In order to monitor the effect of the addition of biodiesel on the lubricity of road diesel, biodiesels produced from sunflower oil and olive oil were used. The use of rape seed oil biodiesel as a diesel fuel substitute is a commercial event in Central Europe; in the United States the soybean oil biodiesel has been examined in detail.

The emissions reduction benefits of Fischer-Tropsch (FT) diesel fuel have been shown in several recent published studies in both engine testing and in-use vehicle testing. FT diesel fuel shows significant advantages in reducing regulated engine emissions over conventional diesel fuel primarily to: its zero sulfur specification, implying reduced particulate matter (PM) emissions, its relatively lower aromaticity, and its relatively high cetane rating. However, the actual effect of FT diesel formulation on the in-cylinder combustion characteristics of unmodified modern heavy-duty diesel engines is not well documented. As a result, a Navistar T444E (V8, 7.3 liter) engine, instrumented for in-cylinder pressure measurement, was installed on an engine dynamometer and subjected to steady-state emissions measurement using both conventional Federal low sulfur pump diesel and a natural gas-derived FT fuel.