Search Results

This study focuses on variable amplitude loadings applied to automotive chassis parts experiencing carmaker’s specific proving grounds. They are measured with respect to time at the wheel centres and composed of the six forces and torques at each wheel, within the standard vehicle reference frame. In the scope of high cycle fatigue, the loadings considered are supposedly acting under the structure yield stress. Among the loadings encountered during the vehicle lifetime, two classes stand out: Driven Road: loads measured during the vehicle manoeuvre; Random Road: loads mainly coming from the road asperity. To separate both effects, a frequency decomposition method is proposed before applying any lifetime assessment methods. The usual Rainflow counting method is applied to the Driven Road signal. These loadings, depending on the vehicle dynamics, are time-correlated. Thus, the load spectra is set only thanks to the vehicle accelerations time-measurement.

The main development targets for future motorcycle and small vehicle propulsion units are the reduction of dimensions, weight, fuel consumption and pollutant emission for a considered power output. The paper presents a concept for the improvement of the thermodynamic process stages consisting on scavenging, mixture formation and combustion - as a main support for achieving the mentioned targets. The concept is exemplified by results in terms of compared indicator diagrams, specific fuel consumption and exhaust gas emissions - in base of numerical simulation and experimental analysis at the engine - respectively at the vehicle test bench.

To provide optimal performance of a small DI diesel in relation to noise, emissions and fuel economy, an experimental investigation was carried out using Taguchi methods. A single cylinder 3.5 kW diesel was selected for performance test at different engine speeds, loads and static injection timings. These controlled parameters were varied at three levels and the resulting changes in response variables viz. engine noise, smoke, HC, NOx, CO, CO2 emissions and fuel economy (b.s.f.c) were observed. The levels for low noise, smoke, emissions and b.s.f.c could be predicted and relevant combination of controlled parameters specified. Confirmation engine runs were carried out and the results showed good agreement with the predicted optimized quantities of interest based on Taguchi analysis. The effect of engine parameters to the above responses was evaluated in terms of percent contributions by using analysis of variance.

THE BATTERY is the primary component limiting electric vehicle performance that equals today's standard of expectations as defined by the I. C. engine powered vehicles. Efforts to optimize the electric vehicle performance is leading many people to select and assemble the highest efficiency components available. High voltage electric vehicle power system can provide performance advantages over lower voltage systems, but only if this voltage is in balance with the total system. Mixing high efficiency components does not Insure total system efficiency optimization. The ability of a battery to release its stored energy is a function of its demand. Higher current demands will reduce the efficiency of a battery. This paper reveals how such a mismatch occurred and its reflection on what appeared to be a battery problem.

The need for efficient space utilization has provided a framework for the design of a 248mm family of torque converters that supports a wide choice of engine and transmission combinations. The axial length of the part and its weight have been substantially reduced while the performance range has been broadened without degradation of efficiency. The new converter operates in an expanded slipping clutch mode. It significantly contributes to the performance and fuel economy improvements of related vehicles. To meet the cost target, the comprehensive lineup and the resulting complexity have required a high level of component interchangeability. During the design phase, the manufacturing core competencies were scrutinized and process redundancies eliminated, both resulting in optimization of material selection and applicable technology.

Effective 1st April 2023, India's automotive emissions regulation has shifted from BS-VI Stage-1 to BS-VI Stage-2 standard the after-treatment systems need to demonstrate robust performance not just on the cycle, but also to demonstrate emissions for on-road Real Driving Emission (RDE) conditions. A stringent On-Board Diagnostics (OBD) strategy to monitor the real-time emission levels along with compliance Road Driving Emissions (RDEs) are focus areas for BS VI Stage-2 emission legislation. The maximum speed on MIDC is 90km/h in BS-VI Stage-1, Diesel Oxidation Catalyst (DOC)+Selective Catalyst Reduction Filter (SCRF®) was able to meet legislation at the lab, and now with the RDE cycle max speed of the vehicles under the M1 category <3.5 T will have the max permitted legal limit shall surpass 100 km/h for not around 3% of the span in the third phase of driving cycle for which max speed is up to 120 km/h.

This paper describes the after-treatment technology that could be used to meet a future BS-VII standard, considering close-coupled SCR (cc-SCR) to help start NOx conversion earlier. Both active (Cu/Fe-SCR based) and passive (V-SCR based) systems have the potential to meet emission limits. V-SCR may be considered in the rear position because V-SCR shows a fast response with very low N2O formation. Next-gen V-SCR technology shows significantly improved performance and durability closer to Cu-SCR. The steady-state NOx conversions over Next-Gen V-SCR were better than BS-VI V-SCR in both fresh and aged-580°C/100h conditions. High durability was also observed after engine aging of 1000h (WHTC + high load). Another big challenge in BS VII could be the PN10 requirement. With enhanced filtration coating (EFC) technology, PN emissions drop drastically in comparison to Euro VI reference without EFC to meet a future BS VII.

Weight reduction of automobiles is key technology in order to improve fuel economy and driving performance. Concerning of the motorcycle engine, weight reduction is also the fundamental and important technologies. Cylinder is one of the main parts of engine and the wear characteristics of the cylinder liner are largely related to the engine performance. Gray iron liners squeezed in aluminum cylinder block have been widely used. This is due to the excellent resistance to abrasion of gray iron. In order to realize light all aluminum cylinder, the good abrasion resistant method is necessary to develop to be applied with inner surface of liners. We have developed the new Rapid Composite Plating System for the motorcycle engine cylinders. This system made it possible to adopt all aluminum cylinders without cast iron liners to new type of engine.

BlueStar Advanced Technology Corporation (BATC) as part of its participation in the USAF/NASA Li Ion Battery Development Consortium has developed a candidate 25-Ah cell for the Mars 2001 Lander. Although the capacity and cycle life requirements for this application are relatively modest, the low temperature performance (−20°C) and pulse discharge requirements (60A) are somewhat more challenging. Geometric requirements within the spacecraft also constrain the cell design leading to a cell with an aspect ratio quite different from those 25-Ah Li ion cells previously developed by BATC. The design of this cell and its compliance with the performance requirements of the mission will be discussed.

Fixed displacement pumps will continue to be a popular choice for hydraulic system designers for decades to come. These pumps are used in almost every industrial and mobile market segment and are generally less expensive than comparable variable displacement type pumps. Fixed displacement “Vane Type” pumps are especially popular because of their low noise characteristics as well as their inherent repair features. The demand for “Vane Type” fixed displacement pumps continues to grow in all market segments. Because of this continued demand, a new design of “fixed displacement vane pumps” is being developed. These pumps, designated the VPF Series, are targeted to offer continuous operating pressures up to 280 BAR with displacements from 40 to 215 cc/rev.

In order to take full advantage of SiC, a high temperature package for power module using SiC devices was designed, developed, fabricated and tested. The details of the material selection and fabrication process are described. High temperature reliability test and power test shows that the package presented in this paper can perform well at the high junction temperature.

Due to the general requirements in the automotive industry to reduce the power consumption, fuel consumption rate and CO2 emission a new HID (High Intensity Discharge) bulb with only 25W is under development for front lighting systems. A first headlamp integrated in a hybrid vehicle is now launched as a first application in the market. The current regulation in ECE allows to get rid of the mandatory headlamp cleaning system and the automatic leveling requirement once the 25W HID bulb is applied. The reason for this is the objective luminous flux of the 25W HID bulb, which emits less than 2000 lm, a boundary defined in the regulation, where a headlamp cleaning and an automatic leveling is requested. That simplifies especially the integration in smaller vehicles and electric and hybrid vehicles. The paper describes the special design of the headlamp, the projector unit, the light performance, packaging advantages and future outlook of further applications in the near future.

This paper describes the set-up and testing of a single cylinder 25cc, air cooled, 4-stroke Spark Ignition (SI) engine converted to run in Homogeneous Charge Compression Ignition (HCCI) mode with the aid of various combustion control systems. The combustion control systems were investigated regarding their effects on combustion stability and heat release phasing. Engine operation was compared with unique findings from previous work done on a very small 2-stroke HCCI engine. HCCI engine operation was possible between 1000 - 4000 rpm when using Diethyl Ether (DEE) as the test fuel. Maximum operational fuel-air equivalence ratio (Φ) was 0.75 when operating without Exhaust Gas Recirculation (EGR). This relatively high equivalence ratio was attainable due to thermal gradients induced by the high surface area to volume ratio of the small engine combustion chamber, resulting in high chamber heat transfer.

The pistons in a snowmobile engine are subjected to severe temperature conditions not only because snowmobiles are operated in extremely cold temperatures but also because the engine has a high output per unit volume of approximately 150kW/liter. The temperature of the piston top may go from -40°C (when a cold engine is started) to 400°C or higher (when the engine is running at full load). When the piston and cylinder inner wall are cold, the performance of the lubricating oil drops; when they are hot, scuffing may be produced by problems such as tearing of the oil film between the piston and cylinder. When the engine is run at full load for a long time, moreover, the piston is subjected to prolonged high-temperature use, which is conducive to the production of piston boss hole abrasion and ring groove adhesive wear.

Preliminary results from testing of 26 X 6.6 radial-belted and bias-ply aircraft tires at NASA Langley's Aircraft Landing Dynamics Facility (ALDF) are reviewed. These tire tests are part of a larger, on going joint NASA/FAA/Industry Surface Traction and Radial Tire (START) Program involving three different tire sizes. The 26 X 6.6 tire size evaluation includes cornering performance tests throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Static test results to define 26 X 6.6 tire vertical stiffness properties are also presented and discussed.

This paper presents a novel battery degradation model based on empirical data from the Racing Green Endurance project. Using the rainflow-counting algorithm, battery charge and discharge data from an electric vehicle has been studied in order to establish more reliable and more accurate predictions for capacity and power fade of automotive traction batteries than those currently available. It is shown that for the particular lithium-iron phosphate (LiFePO₄) batteries, capacity fade is 5.8% after 87 cycles. After 3,000 cycles it is estimated to be 32%. Both capacity and power fade strongly depend on cumulative energy throughput, maximum C-rate as well as temperature.

A surface modification method by electrical discharge has been developed for the valve seats of aluminum cylinder heads. This method employs a conventional electrical discharge machine to generate continuous discharge arcs between an electrode and a cylinder head, whereby the molten electrode material is transferred and clad onto the valve seat area on the cylinder head. Using this new cladding method, a wear-resistant cladding can be formed on each valve seat area in a matter of minutes and, if the same number of electrodes as valve seat areas are set one on one, all the valve seat areas can be clad simultaneously. The advantages of this method include local cladding capability, outstanding adhesion, quick cladding speed, and excellent adaptability to various types of engines. The chemical composition of the cladding was determined by a preliminary test using dynamo engines, and the durability of the cladding was evaluated using the same dynamo engines.

Sundstrand is investigating 270-Vdc/hybrid 115-Vac electrical power generating and distribution systems technology so as to be well prepared to offer such systems for future aircraft applications. The approach taken has been to design, build, and test a representative system that meets or exceeds the tightest of the performance standards as defined by miliary standards. This paper describes a single-channel, 120-kW hybrid system and presents some typical performance data. The dc bus supplies a 30-kVA, 400-Hz, 115-Vac inverter; constant power load banks of up to 150 kW; and a resistive load bank of up to 90 kW. System simulation studies indicated the potential for unstable operation due to the negative impedance of the constant power load in conjunction with the source ripple filter and the load EMI filters. Unstable voltage and current were observed in system testing when the magnitude of the source impedance was not sufficiently below that of the load impedance.

Sundstrand has been investigating 270-Vdc/hybrid 115-Vac electrical power generating systems (EPGS) technology in preparation for meeting the electrical power generating system (EPGS) requirements for future aircraft (1). Systems such as the one being investigated are likely to be suitable for the More-Electric Aircraft (MEA) concepts presently under industry and military study. The present Sundstrand single-channel testbed is being further expanded to better understand the electrical system performance characteristics and power quality requirements of an MEA in which traditional mechanical subsystems are replaced by those of a “more-electric” nature. This paper presents the most recent Sundstrand 270-Vdc system transient performance data, and describes the modifications being made to the 270-Vdc/hybrid 115-Vac testbed.

Innovative Power Solutions (IPS), LLC has developed a 300A and a 500A 28 VDC Brushless Wound Rotor Starter/Generator (S/G) system. These systems are capable of replacing brush type S/G or Air Turbine Starters by presenting an adequate Torque vs. Speed performance. The S/G system developed by IPS consists of the Starter/Generator (Motor/Generator) and S/G Control Unit (SGCU).