Search Results

A multi-zone model for the prediction of performance and emissions of indirect injection diesel engines is presented. The interaction between turbulent mixing and chemical reaction, which primarily controls combustion, is described as a stochastic process by means of a Monte Carlo collision-dispersion model. The major contribution of the present work lies in combining such an approach with improved models of fuel evaporation in supercritical conditions, burning rate, radiative heat transfer and flow coefficient of the passageway, besides properly accounting for the real gas effects. A limited number of empirical correlations was introduced, so obtaining a rather general and physically meaningful predictive tool. Experimental data concerning a small single-cylinder engine have been employed to validate the computational procedure.

Liquid fuel penetration was measured using an endoscopebased imaging system in an operating single-cylinder heavy-duty direct injection diesel engine with simulated turbocharging. Sprays were imaged via the elastic backscatter technique without significantly altering the engine geometry. Light loads (or pilot injections) were also studied because the spray breakup, mixing and vaporization processes can be isolated since they are less influenced by heat feedback from the flame than in a full injection case. The pilot injections included cases with three different fuel amounts (10%, 15% and 20% of the fuel injected in the baseline case, i.e., 75% load and 1600 rev/min) with different start-of-injection timings. Maximum liquid penetration lengths beyond which the fuel is completely vaporized were observed for all the cases studied. The maximum lengths varied from 23 mm to 28 mm for the different start-of-injection timings.

Cycle-to-cycle variations in the pressure evolution within the cylinder of a spark ignition engine has long been recognized as a phenomenon of considerable importance. In this work, use of tools borrowed to the nonlinear dynamical system theory to investigate the time evolution of the cylinder pressure is explored. By computing a divergence rate between different pressure cycles versus crank angle, four phases during the combustion cycle are exhibited. These four phases may be identified with the four common phases evidenced by burn rate calculations [1]. Starting from phase portraits and using Poincaré sections, we also study correlations between peak pressures, IMEP and the durations from ignition to appearance of a flame kernel.

Computational analysis of flow field inside a high pressure swirl injector is carried out. The effects of injection pressure and internal geometry on velocity field inside the nozzle and especially at the injector exit are studied in detail. From the velocity distribution at the exit plane, methods to determine the discharge coefficient and liquid sheet cone angle are given. To validate the computational model, the spray cone angles in the immediate vicinity of the nozzle exit were measured from photographs over the injection pressure differential range of 3.5 to 10.3 MPa. Static flow rates were measured using a flow meter over the same pressure range. The calculated results are found to be consistent with the experimental measurements. Extensive calculations were then conducted to examine the influence of swirl inlet port area and orifice diameter on discharge coefficient and spray cone angle.

An experimental investigation is carried out on in-cylinder motion, during the intake and compression strokes of a spark-ignited multi-valve engine. This study is conducted on a single cylinder four valve research engine. The engine is equipped with several optical accesses on cylinder liner and cylinder head. The turbulence and local velocity in combustion chamber were measured by Laser Doppler Velocimetry. Furthermore, effects of different bowl shapes on turbulence, cycle by cycle flow variations, and tumble distortion were studied. Tumble velocity field exhibits a triplet vortices structure composed of one vertical and two horizontal vortices. This structure is induced during the inlet stroke, and remains during compression. In the latest stage of compression, tumble is converted into a pair of horizontal vortices. Velocity measurements in the cylinder show a precession motion of tumble center. Distortion of tumble is very unstable and perturbed with a flat top piston.

Temperature measurement of internal components and surfaces can enhance understanding of thermal processes that occur during engine operation. Such measurements have typically been made with thermocouples, temperature sensitive paints or plugs, or infrared emission methods. Phosphor thermometry, a non-contact measurement technique, is an alternative that can be applied when more traditional methods are not feasible or are too costly. Recent efforts described in this paper have used phosphor thermometry to measure steady state piston crown temperature in a single cylinder engine. Additional testing with this technique included monitoring intake valve temperature in a multicylinder engine under cold start conditions. Packaging of the optical hardware necessary for this technique was substantially refined during these tests for use in modern engine geometries.

The paper describes a water analogy rig and its associated instrumentation and data acquisition system, developed to make particle image velocimetry (PIV) measurements of in-cylinder flow during the intake stroke. Methods of producing parameters to describe the flow characteristics of four valve engines with tumbling air motion are evaluated and correlation with combustion performance is examined for two different engines with a total of seven different inlet port designs. Each inlet port configuration was also evaluated by conventional steady flow methods. The results show that the dynamic water flow rig gave improved correlation with combustion data than that obtained with conventional steady flow methods of characterising in-cylinder flow patterns.

A combustion-based analytical method, initially developed by the Southwest Research Institute (SwRI) and referred to as the Constant Volume Combustion Apparatus (CVCA), has been further researched/developed by an SwRI licensee (Advanced Engine Technology Ltd.). This R&D has resulted in a diesel fuel Ignition Quality Tester (IQT) that permits rapid and precise determination of the ignition quality of middle distillate and alternative fuels. Its features, such as low fuel volume requirement, complete test automation, and self-diagnosis, make it highly suitable for commercial oil industry and research applications. A preliminary investigation, reported in SAE paper 961182, has shown that the IQT results are highly correlated to the ASTM D-613 cetane number (CN). The objective of this paper is to report on efforts to further refine the original CN model and report on improvements to the IQT fuel injection system.

A vehicle's evaporative emission control system is continuously working, even when the vehicle is not running, due to generation of vapors from the fuel tank during ambient temperature variations. Diurnal temperature cycles cause the fuel tank to breathe the fuel vapor in and out, and thus the activated carbon canister is constantly loading and purging the hydrocarbon vapors. This paper discusses a study undertaken at Ford to evaluate the relationship between carbon canister condition and fuel tank vapor generation during diurnal cycles. The results of an extensive set of experiments are presented, and the data from these experiments are compared to the output of a fuel vapor system model also developed at Ford. Key parameters relating to the migration of hydrocarbons during the experimental conditions studied, including initial canister condition, canister volume, and canister geometry, are discussed.

A 1.9L four cylinder engine was evaluated for leakage of cylinder charge through the exhaust valve seats. Fast FID HC analyzer traces reveal leakage. Static leakdown tests do not correlate with the Fast FID measurement, unlike previously published reports for a different engine. The causes of exhaust valve seat leakage are likely to be Flakes of cylinder deposits lodging in the valve seat Valve seat distortion due to the thermal and pressure loading of the cylinder head structure Because deposit related effects are very history dependent, it is very difficult to obtain quantitative results. Some experimental observations: Static pressure leakage measurements show variation of leakage area with cylinder pressure, caused by flexing of the valve head. Dynamic leakage results are history dependent. Leakage is reduced after running at high speed/load, and gradually build up during extended light load low speed operation.

Catastrophic failures of fuel pumps used to transport ethanol have occurred in various facilities. Failures occurred in as little as 50 hours on pumps with a 2000 hour life expectancy. Post-failure inspection of the pumps showed corrosive pitting of the metal in the areas of sliding contact. Several potential causes, including cavitation, thermal expansion of pump parts, and fuel contaminants such as acetic acid were ruled out. Fuel samples from facilities with high pump failure rates passed all D 4806 specification tests for fuel-grade ethanol, including titratable acid by D 1613. However, pH readings as low as 2.0 indicated potentially corrosive fuels. Controlled tests on pumps and corrosion tests showed that pump failures correlated with fuel pH. Corrosive fuels were found to contain ethyl sulfate, which correlated with fuel pH. It appears that ethyl sulfate originates from sulfur dioxide, which is used as an antioxidant and antiseptic in the production of ethanol.

Three catalysts based on X-zeolite have been developed by exchanging its Na+ ion with Copper, Nickel and Vanadium metal ions and tested in a stationary SI engine exhaust to observe their potentialities for NOx and CO controlling. The catalyst Cu-X, in comparison to Ni-X and V-X, exhibits much better NOx and CO reduction performance at any temperature. Maximum NOx conversion efficiencies achieved with Cu-X, Ni-X and V-X are 62.2%, 59.7% and 56.1% respectively. Unlike noble metals, the doped X-zeolite catalysts, studied here, maintain their peak NOx reduction performance through a wider range of A/F ratio. Back pressure developed across the catalyst bed is found to be well within the acceptable limits.

Four vehicle fleets, consisting of 3 to 4 vehicles each, were emission tested on a 48″ roll chassis dynamometer using both the FTP urban dynamometer driving cycle and the REP05 driving cycle. The REP05 cycle was developed to test vehicles under high speed and high load conditions not included in the FTP. The vehicle fleets consisted of 1989 light-duty gasoline vehicles, 1992-93 limited production FFV/VFV methanol vehicles, 1992-93 compressed natural gas (CNG) vehicles and their gasoline counterparts, and a 1992 production and two prototype ethanol FFV/VFV vehicles. All vehicles (except the dedicated CNG vehicles) were tested using Auto/Oil AQIRP fuels A and C2. Other fuels used were M85 blended from A and C2, E85 blended from C1, which is similar to C2 but without MTBE, and four CNG fuels representing the range of in-use CNG fuels. In addition to bag measurements, tailpipe exhaust concentration and A/F data were collected once per second throughout every test.

This paper introduced a very simple method to measure the liquid phase of spray in an optically accessible DI diesel engine. Particular attention was paid to easy usage and maintaining the compression ratio of the real engine. As a result, a less-expensive 4 W argon laser was used as the beam source and an E-10 high-speed camera was used for continuously observing the elastic-scatter liquid phase image. Meanwhile, the compression ratio can be kept as the real engines by this method. Through this method, the effects such as injection pressure, nozzle specification, intake air boost and temperature on liquid phase penetration before ignition were investigated. Reducing nozzle hole diameter decreased the length of the liquid phase. Increasing injection pressure hastened the evolution of liquid phase, while the liquid phase length varied complexly. Increasing intake air boost considerably shortened the liquid phase penetration and ignition delay.

In this study, we investigated the combustion technology for the direct injection (DI) methanol engine for a heavy-duty vehicle that makes use of the fuel characteristics of methanol and achieves smokeless burning with high efficiency and low NOx emissions under the heavy load condition. A 3.3-liter 4-cylinder spark-assisted DI methanol engine was tested to investigate the combustion and NOx emission characteristics under the full load condition with supercharging and/or EGR. We believe that supercharging suppressed the stratified charge combustion, but accelerated the premixed combustion to increase the indicated mean effective pressure. Moreover, supercharging was helpful in carrying out EGR under the full load condition without deteriorating the thermal efficiency. Furthermore, heavy EGR during supercharging reduced the NOx emissions dramatically while maintaining the high thermal efficiency and controlling the unburned hydrocarbons emissions.

The cycle-resolved fuel concentration near the spark plug in a firing SI engine has been measured using an infrared fiber optic instrumented spark plug probe. The probe can measure in-cylinder concentrations of hydrocarbons in the pre-combustion regions of the engine cycle and give qualitative results for unburned hydrocarbons in the post-combustion regions. The device consists of a spark plug body that has been modified to accept a pair of sapphire optical fibers in addition to a spark electrode. Radiation from an infrared source is coupled into one fiber and reflected from a minor on the spark plug ground electrode to the other fiber which carries the signal to a detector and data acquisition system. The probe measures the attenuation of the infrared radiation transmitted through a region in the vicinity of the spark gap. The attenuation results from the absorption of radiation by the fuel. The measurements were made in a CFR engine at 600 rpm using propane fuel.

Industrial grade ethanol, in concentrations ranging from 130 proof to 200 proof, can be used as a feedstock for a 50kWe advanced fuel processor developed by Arthur D. Little, Inc. for fuel cell vehicles. At 180 proof concentration, hydrated ethanol showed no performance degradation compared with both 200 proof (pure) ethanol and E95 (95% ethanol and 5% gasoline) at equivalence ratios ranging from 3.0 to 4.0. Environmental benefits associated with the use of ethanol in fuel cell power systems include its production from renewable biological sources, low toxicity in the event of an accidental spill, and recycling of carbon dioxide released by the process back to the plant matter used as ethanol feedstock. Cost savings associated with the use of hydrated ethanol are expected to include lower production costs, lower distribution costs, and lower powerplant costs due to the possibility of system simplification.

This paper presents some experimental results of air velocity measurements near high pressure diesel sprays. The measurements were made using a moderately high pressure (90 MPa) common rail injector in a pressurized spray chamber. The chamber was operated at ambient temperature (25°C) and was pressurized with Argon to produce a chamber gas density of about 27 kg/m3, similar to densities found in a large turbocharged diesel near TDC. The gas phase was tagged using water droplets doped with Stilbene 420, with an estimated droplet size of 18 μm. The atomized water-Stilbene droplets were illuminated with the third harmonic of a pair of Nd:YAG lasers which caused the Stilbene to fluoresce at about 420 nm. To reduce the competing fluorescence from the injected fuel, the injector was fueled with Jet-A fuel. Using the two lasers, double exposures of the small droplets were recorded on film. The laser pulse lengths were about 6 ns, and typical times between pulses were 100 μs.

Automatic transmission clutches are complex tribological systems. Frictional performance is controlled by the interaction of base fluids, additive components, composition clutches, and steel reaction plates with varying energy inputs and thermal stresses in an oxidizing environment. This paper, rather than addressing fully formulated fluid performance in such a system, takes a more fundamental approach where the number of system variables is reduced and the relative effects of formulation variables on system performance can be better examined. Relationships among observed friction performance, system oxidation, friction member condition, and representative performance additives are explored using a synthetic base fluid and a conventionally refined mineral base fluid.

The Cooperative Lubrication Research (CLR) Oil Test Engine, usually called the L-38, has been used for nearly 25 years to evaluate copper-lead journal bearing protection of gasoline rnotoroils under high-temperature, heavy-duty conditions. The test is sensitive to aggressive surface active additives that may encourage bearing corrosion. The L-38 also provides an estimate of oil durability, assessing the resistance of an oil to the accumulation of acidic by-products of combustion that could attack copper-lead bearings. However, the L-38 engine dynamometer test uses a heavily leaded gasoline that is no longer representative of the commercial fuels available in North America, Europe, or Japan. Rather than discard the L-38, this paper describes work to modify the L-38 procedure to run with unleaded gasoline.