Search Results

In-service emissions measurements were conducted on two package delivery trucks: one model year 2008 FCCC MT-55 conventional diesel and one model year 2012 FCCC MT-55 hydraulic hybrid (HHV). Mass emissions of CO2, CO, NOx, PM, and THC from the HHV and the conventional diesel test vehicle were each measured under conditions closely simulating normal package delivery operation. The HHV demonstrated a 29.4% improvement in fuel economy and a 17.4% reduction in CO2 emissions compared to the conventional diesel vehicle. The HHV showed its best potential in operating areas characterized by low driving speeds and high number of stops (“pick-up and delivery”) with a 40.5% improvement in fuel economy and a 21.2% reduction in CO2 emissions.

Selective Catalytic Reduction (SCR) systems have been demonstrated as effective solutions for controlling NOx emissions from Heavy Duty diesel engines. Future HD diesel engines are being designed for higher engine out NOx to improve fuel economy, while discussions are in progress for tightening NOx emissions from HD engines post 2020. This will require increasingly higher NOx conversions across the emission control system and will challenge the current aftertreatment designs. Typical 2010/2013 Heavy Duty systems include a diesel oxidation catalyst (DOC) along with a catalyzed diesel particulate filter (CDPF) in addition to the SCR sub-assembly. For future aftertreatment designs, advanced technologies such as cold start concept (dCSC™) catalyst, SCR coated on filter (SCRF® hereafter referred to as SCR-DPF) and SCR coated on high porous flow through substrates can be utilized to achieve high NOx conversions, in combination with improved control strategies.

Heavy-duty diesel engines are used in different application areas, like long-haul, city distribution, dump truck and building and construction industry. For these wide variety of areas, the engine performance needs to comply with the real-world legislation limits and should simultaneously have a low fuel consumption and good drivability. Meeting these requirements takes substantial development and calibration effort, where an optimal fuel consumption for each application is not always met in practice. TNO's Integrated Emission Management (IEM) strategy, is able to deal with these variations in operating conditions, while meeting legislation limits and obtaining on-line cost optimization. Based on the actual state of the engine and aftertreatment, optimal air-path setpoints are computed, which balances EGR and SCR usage.

In recent years urea selective catalytic reduction (SCR) has become the principal method of NOx abatement within heavy duty (HD) diesel exhaust systems; however, with upcoming applications demanding NOx reduction efficiencies of above 96 % on engines producing upwards of 10 g·kWh−1 NOx, future diesel exhaust fluid (DEF) dosing systems will be required to operate stably at significantly increased dosing rates. Developing a dosing system capable of meeting the increased performance requirements demands an improved understanding of how DEF sprays interact with changing exhaust flows. This study has investigated four production systems representing a diverse range of dosing strategies in order to determine how performance is influenced by spray structure and identify promising strategies for further development. The construction of an optically accessible hot-air flow rig has enabled visualisation of DEF injection into flows representative of HD diesel exhaust conditions.

This study was aimed at experimentally investigating the impact of diesel/natural gas (NG) dual-fuel retrofitting onto gaseous emissions emitted by i) legacy, model year (MY) 2005 heavy-duty engines with cooled EGR and no after-treatment system, and ii) a latest technology engine equipped with DPF and urea-SCR after-treatment systems that is compliant with 2010 US-EPA emissions standards. In particular, two different dual-fuel conversion kits were evaluated in this study with pure methane (CH4) being used as surrogate for natural gas. Experiments were conducted on an engine dynamometer over a 13-mode steady-state test cycle as well as the transient FTP required for engine certification while gaseous emissions were sampled through a CVS system. Tailpipe NOx emissions were observed at a comparable level for diesel and diesel/CH4 dual-fuel operation for the 2010 compliant engine downstream the SCR.

The potential of drag reduction on a generic model of a heavy vehicle using base flaps operated in combination with flow control devices is investigated experimentally. Base flaps are well known as drag reduction devices for bluff bodies and heavy road vehicles. However, for optimal performance their deflection angle should typically not exceed 12°. In this paper the primary goal is to increase the usable range of the deflection angles by applying flow control. The secondary goal is to find the most suitable method for flow control. A comparison is made between triangular vortex generators and fluidic oscillators as passive and active flow control methods, respectively. Vortex generators have the advantage of being very simple devices but produce drag. Fluidic oscillators are also quite simple devices but require additional air supply. Their advantages are that they can be activated when needed and that they do not generate additional drag.

The impact of Reynolds number on the aerodynamics and operational performance of commercial vehicles is discussed. All supporting data has been obtained from published experimental and computational studies for complete vehicles and vehicle components. A review of Reynolds number effects on boundary layer state, unsteady and steady flow, time dependent wake structure, interacting shear layer and separated flows is presented. Reynolds number modeling and simulation criteria that impact aerodynamic characteristics and performance of a commercial vehicle are shown. The concepts of dimensional analysis and flow similarity are employed to show that aerodynamics of commercial ground vehicles is only dependent on Reynolds number. The terminology of Roshko is adopted for discussing the variation in drag with Reynolds number in which the subcritical, transitional and transcritical flow regimes are defined for commercial vehicles.

Using lift axles enables fleet to increase the load capacity of a vehicle, eliminating the need for multiple trips, thus reducing operational costs. In a project to assess the potential of reducing fuel consumption and greenhouse gas (GHG) emissions by lifting axles on unloaded semi-trailers, lift axle regulations in various jurisdictions and the studies that led to these regulations were analyzed. The SAE Fuel Consumption Test Procedures Type II (J1321) was used for fuel consumption track test evaluations. The tests were conducted on unloaded two-axle van semi-trailers, four-axle van semitrailers, and B-trains, and resulted in fuel savings of 1.3% to 4.8%, depending on vehicle configuration and the number of axles lifted during the test.

Modern aerodynamic Class 8 freight tractors can improve vehicle freight efficiency and fuel economy versus older traditional style tractors when pulling Canadian style A- or B-Train double trailer long combination vehicles (LCV's) at highway speeds. This paper compares the aerodynamic performance of a current generation aerodynamic tractor with several freight hauling configurations through computational fluid dynamics evaluations using the Lattice-Boltzmann methodology. The configurations investigated include the tractor hauling a standard 53′ trailer, a platooning configuration with a 30′ separation distance, and an A-Train configuration including two 48′ trailers connected with a dolly converter. The study demonstrates CFD's capability of evaluating extremely long vehicle combinations that might be difficult to accomplish in traditional wind tunnels due to size limitations.

This paper conducts experimental study and numerical large eddy simulation for the drag reduction effect of jet boat-tail passive flow control on bluff body models. The jet boat-tail for bluff bodies operates by surrounding a converging duct around the end of a bluff body where the base surface is located. The duct captures free stream and forms a high speed jet angled toward the center of the bluff body base surface circumferentially to have the effect of a boat tail. A rectangular prism bluff body representative of various motor vehicle shapes such as trucks, vans, SUVs is used in this study. The numerical Large Eddy Simulation shows that the jet boat-tail sucks in the forebody boundary layer due to the low base pressure and significantly thins the boundary layer. The jet interacts with the shear layer and creates large vortex structures that entrain the freestream to base flow and energize it.

The performance of several aerodynamic technologies and approaches, such as trailer skirts, trailer boat tails, gap reduction, was evaluated using track testing, model wind tunnel testing, and CFD simulation, in order to assess the influence of the design, position and combination of various aerodynamic devices. The track test procedure followed the SAE J1321 SAE Fuel Consumption Test Procedure - Type II. Scale model wind tunnel tests were conducted to have direct performance comparisons among several possible configurations. The wind tunnel tests were conducted on a 1/8 scale model of a tractor in combination with a 53-foot semi-trailer. Among others, the wind tunnel tests and CFD simulations confirmed the influences of trailer skirts' length observed during the track tests and that the wider skirt closer to the ground offer better results. The differences in the shape, dimensions and position of rear deflectors and trailer skirts on the trailer are reflected in the test results.

The flow-field around a “common” European heavy truck, equipped with several different trailer devices, is investigated using steady and unsteady simulations. This work demonstrates how with simple devices added on the trailer it is possible to strongly decrease the aerodynamic drag over 10%, with an increase of overall dimensions below 1% without any change to the load capacity of the trailer. Several devices, installed on the trailer, are tested on a target vehicle and the shape of the “airbag”, the “fin”, the “boat tail” and the “front-rear trailer device” has been optimized to achieve the maximum in drag reduction in front wind. The performance of the optimized devices are tested also in cross wind conditions with the yaw angle varying from 0° to 30°. The truck equipped with the front-rear trailer device is also investigated using time variant simulation with yaw angle of 0°, 5°, 10°.

The three parameter Ramberg-Osgood (RO) method finds popular usage for extracting complete stress-strain curve from limited data which is usually available. The currently popular practice of assuming the plasticity to set in only at the Yield point provides computational advantage by separating the complete nonlinear curve, obtained from RO method, into elastic and plastic regions. It is shown, with an example problem, that serious errors are committed by using this method if one compares the obtained results with results of complete stress-strain curve. In the present work we propose a simple Taylor series based approach based on RO method to overcome the above deficiency. This method is found to be computationally efficient. The proposed method is applicable for stress-strain curves of materials for which RO method provides a good approximation.

Annual fuel use for sleeper cab truck rest period idling is estimated at 667 million gallons in the United States, or 6.8% of long-haul truck fuel use. Truck idling during a rest period represents zero freight efficiency and is largely done to supply accessory power for climate conditioning of the cab. The National Renewable Energy Laboratory’s CoolCab project aims to reduce heating, ventilating, and air conditioning (HVAC) loads and resulting fuel use from rest period idling by working closely with industry to design efficient long-haul truck thermal management systems while maintaining occupant comfort. Enhancing the thermal performance of cab/sleepers will enable smaller, lighter, and more cost-effective idle reduction solutions. In addition, if the fuel savings provide a one- to three-year payback period, fleet owners will be economically motivated to incorporate them.

This paper addresses scheduling of quantized power levels (including part load operation and startup/shutdown periods) for a propane powered solid oxide fuel cell (SOFC) hybridized with a lithium-ion battery for a tracked mobile robot. The military requires silent operation and long duration missions, which cannot be met by batteries alone due to low energy density or with combustion engines due to noise. To meet this need we consider an SOFC operated at a few discrete power levels where maximum system efficiency can be achieved. The fuel efficiency decreases during transients and resulting thermal gradients lead to stress and degradation of the stack; therefore switching power levels should be minimized. Excess generated energy is used to charge the battery, but when it’s fully charged the SOFC should be turned off to conserve fuel.

We have recently obtained experimental data and used them to develop computational models to quantify occupant impact responses and injury risks for military vehicles during frontal crashes. The number of experimental tests and model runs are however, relatively small due to their high cost. While this is true across the auto industry, it is particularly critical for the Army and other government agencies operating under tight budget constraints. In this study we investigate through statistical simulations how the injury risk varies if a large number of experimental tests were conducted. We show that the injury risk distribution is skewed to the right implying that, although most physical tests result in a small injury risk, there are occasional physical tests for which the injury risk is extremely large. We compute the probabilities of such events and use them to identify optimum design conditions to minimize such probabilities.

Design of military vehicle needs to meet often conflicting requirements such as high mobility, excellent fuel efficiency and survivability, with acceptable cost. In order to reduce the development cost, time and associated risk, as many of the design questions as possible need to be addressed with advanced simulation tools. This paper describes a methodology to design a fuel efficient powerpack unit for a series hybrid electric military vehicle, with emphasis on the e-machine design. The proposed methodology builds on previously published Finite element based analysis to capture basic design features of the generator with three variables, and couples it with a model reduction technique to rapidly re-design the generator with desired fidelity. The generator is mated to an off the shelf engine to form a powerpack, which is subsequently evaluated over a representative military drive cycles.

The pursuit of greater fuel economy in internal combustion engines requires the optimization of all subsystems including thermal management. The reduction of cooling power required by the electromechanical coolant pump, radiator fan(s), and thermal valve demands real time control strategies. To maintain the engine temperature within prescribed limits for different operating conditions, the continual estimation of the heat removal needs and the synergistic operation of the cooling system components must be accomplished. The reductions in thermal management power consumption can be achieved by avoiding unnecessary overcooling efforts which are often accommodated by extreme thermostat valve positions. In this paper, an optimal nonlinear controller for a military M-ATV engine cooling system will be presented. The prescribed engine coolant temperature will be tracked while minimizing the pump, fan(s), and valve power usage.

Assessing the dynamic performance of multilayer plates subjected to impulsive loading is of interest for identifying configurations that either absorb energy or transmit the energy in the transverse directions, thereby mitigating the through-thickness energy propagation. A reduced-order modeling approach is presented in this paper for rapidly evaluating the structural dynamic performance of various multilayer plate designs. The new approach is based on the reverberation matrix method (RMM) with the theory of generalized rays for fast analysis of the structural dynamic characteristics of multilayer plates. In the RMM model, the waves radiated from the dynamic load are reflected and refracted at each interface between layers, and the waves within each layer are transmitted with a phase lag. These two phenomena are represented by the global scattering matrix and the global phase matrix, respectively.

1 One issue raised by the use of austenitic stainless steels in commercial vehicles is the increase in material costs. To reduce those material costs, a nitric acid electropolishing treatment was applied to SUS436L (18 Cr - 1.5 Mo - 0.4 Nb) and corrosion tests were conducted to compare its corrosion resistance to that of SUS316L(16 Cr - 12 Ni - 2 Mo). Compared to SUS316L, SUS436L subjected to nitric acid electropolishing indicated superior corrosion resistance. In addition, XPS and TEM analyses showed that while the SUS436L passivation film layer contained approximately twice as much chromium, its thickness was also generally reduced by approximately half, to 2 nm. These results suggest that electropolishing with nitric acid, which is highly oxidative, formed a fine passivation film.