Search Results

Wind noise is a significant source of interior noise in automobiles at cruising conditions, potentially creating dissatisfaction with vehicle quality. While wind noise contributions at higher frequencies usually originate with transmission through greenhouse panels and sealing, the contribution coming from the underbody area often dominates the interior noise spectrum at lower frequencies. Continued pressure to reduce fuel consumption in new designs is causing more emphasis on aerodynamic performance, to reduce drag by careful management of underbody airflow at cruise. Simulation of this airflow by Computational Fluid Dynamics (CFD) tools allows early optimization of underbody shapes before expensive hardware prototypes are feasible. By combining unsteady CFD-predicted loads on the underbody panels with a structural acoustic model of the vehicle, underbody wind noise transmission could be considered in the early design phases.

The turbulent boundary layer (TBL) that forms on the outside of a commercial airplane in flight is a significant source of noise. During cruise, the TBL can be the dominant source of noise. Because it is a significant contributor to the interior noise, it is desirable to predict the noise due to the TBL. One modeling approach for the acoustic prediction is statistical energy analysis (SEA). This technique has been adopted by North American commercial airplane manufacturers. The flow over the airplane is so complex that a fully resolved pressure field required for noise predictions is not currently analytically or numerically tractable. The current practice is to idealize the flows as regional and use empirical models for the pressure distribution. Even at this level of idealization, modelers do not agree on appropriate models for the pressure distributions. A description of the wall pressure is insufficient to predict the structural response. A structural model is also required.

As part of the aircraft certification process, landing gear has to be certified against particular risks such as bird and tyre impact cases. According to international aviation regulations, it has to be demonstrated that the landing gear is designed to ensure the capability for continued safe flight and landing after bird impact or after tyre impact resulting from wheel or tyre failure. Structural parts such as the down-lock mechanism must be validated against these requirements since their structural integrity is essential to ensure landing gear down-locking for landing and subsequent on ground movement. Recently, MESSIER-BUGATTI-DOWTY has been involved in the development of explicit analysis in support of bird and tyre impact justification. A model of the down-lock mechanism has been developed and a full scale test has been set up in order to demonstrate the validity of the analysis.

In the development of a more accurate laboratory scale method, the ability to replicate the thermal oxidative degradation mechanisms seen in gas turbine lubricants, is an essential requirement. This work describes an investigation into the influence of key reaction parameters and the equipment set up upon extent and mechanism of oil degradation. The air flow rate through the equipment was found to be critical to both degradation rate and extent of volatilization loss from the system. As these volatile species can participate in further reactions, it is important that the extent to which they are allowed to leave the test system is matched, where possible, to the conditions in the gas turbine. The presence of metal specimens was shown to have a small influence on the rate of degradation of the lubricant. Loss of metal from the copper and silver specimens due to the mild corrosive effect of the lubricant was seen.

Body motions of flying animals can be very complex, especially when the body parts are greatly flexible and they interact with the surrounding fluid. The wing kinematics of an animal flight is governed by a large number of variables and thus the measurement of complete flapping flight is not so simple, making it very complex to understand the contribution of each parameter to the performance and hence, to decide the important parameters for constructing the kinematic model of a bat is nearly impossible. In this paper, the influence of each parameter is uncovered and the variables that a specified reconstruction of bat flight should include in order to maximally reconstruct actual dimensional complexity, have been presented in detail. The effects of the different kinematic parameters on the lift coefficient are being resulted.

To get a sequence retainable rainflow cycle counting algorithm for fatigue analysis, an alternate equivalent explanation to rainflow cycle counting is introduced, based on which an iterative rainflow counting algorithm is proposed. The algorithm decomposes any given load-time history with more than one crest into three sub-histories by two troughs; each sub-history with more than one crest is iteratively decomposed into three shorter sub-histories, till each sub-history obtained contains only one single or no crest. Every sub-history that contains a single crest corresponds to a local closed (full) cycle. The mean load and alternate load component of the local cycle are calculated in parallel with the iterative procedure.

In electronic vehicles (EVs) or hybrid electronic vehicles (HEVs), an inverter system has a direct-current-link capacitor (DC-link capacitor) which provides reactive power, attenuates ripple current, reduces the emission of electromagnetic interference, and suppresses voltage spikes. A film capacitor has been used as the DC-link capacitor in high level power system, but the film capacitor's performance has deteriorated over operating time. The decreasing performance of the film capacitor may cause a problem when supplying and delivering energy from the battery to the vehicle's power system. Therefore, the lifetime prediction of the film capacitor could be one of critical factors in the EVs and HEVs. For this reason, the lifetime and reliability of the film capacitor are key factors to show the stability of the vehicle inverter system. There are a lot of methods to predict the lifetime of the film capacitor.

There are a number of numerical and experimental studies of the aerodynamic performance of wheels that have been published. They show that wheels and wheel-housing flows are responsible for a substantial part of the total aerodynamic drag on passenger vehicles. Previous investigations have also shown that aerodynamic resistance moment acting on rotating wheels, sometimes referred to as ventilation resistance or ventilation torque is a significant contributor to the total aerodynamic resistance of the vehicle; therefore it should not be neglected when designing the wheel-housing area. This work presents a numerical study of the wheel ventilation resistance moment and factors that affect it, using computational fluid dynamics (CFD). It is demonstrated how pressure and shear forces acting on different rotating parts of the wheel affect the ventilation torque. It is also shown how a simple change of rim design can lead to a significant decrease in power consumption of the vehicle.

A simulation framework for vehicle aerodynamics using up to 10 billion fully unstructured cells has been developed on a world-fastest class supercomputer, called the K computer, in Kobe, Japan. The simulation software FrontFlow/red-Aero was fully optimized on the K computer to utilize up to 10,000 processors with tens of thousands of cores. A hybrid parallelization method using MPI among processors and OpenMP among cores inside each processor was adopted. The code was specially tuned for unsteady aerodynamic simulation including large-eddy simulation, and low Mach number approximation was adopted to avoid excessive iterations usually required for the fully incompressible algorithm. The automated mesh refining system was developed to generate unstructured meshes of up to 10 billion cells. In the system, users only generate unstructured meshes in the order of tens of millions of cells directly using commercial preprocessing software.

Uneven wing deployment of a Hybrid Projectile (HP), an Unmanned Aerial Vehicle (UAV) that is ballistically launched and then transforms, was investigated to determine the amount of roll and pitch produced during wing deployment. During testing of an HP prototype, it was noticed that sometimes the projectile began to slightly roll after the wings were deployed shortly after apogee. In this study, an analytical investigation was done to determine how the projectile body dynamics would be affected by the wings being deployed improperly. Improper and uneven wing deployment situations were investigated throughout the course of this study. The first analyzed was a single wing delaying to open. The second was if only one wing was to lock into a positive angle of incidence. The roll characteristics when both wings were deployed but only one was locked into an angle of incidence resulted in a steady state roll rate of 4.5 degrees per second.

The development of the More-Electric Engine (MEE) concept will see an expansion in the power levels, functionality and criticality of electrical systems within engines. However, to date, these more critical electrical systems have not been accounted for in existing engine certification standards. To begin to address this gap, this paper conducts a review of current engine certification standards in order to determine how these standards will impact on the design requirements of More-Electric Engine (MEE) electrical system architectures. The paper focuses on determining two key architectural requirements: the number of individual failures an architecture can accommodate and still remain functional and the rate at which these failures are allowed to occur.

The More Electric Aircraft (MEA) concept coupled with recent advances in power electronics has seen an increasing number of on-board tasks being facilitated by electrical power, as opposed to more conventional hydraulic, mechanical and pneumatic power systems. The migration to a predominantly electrical power system is expected to bring significant cost and performance benefits; however, the devices used to facilitate this change have led to an increasingly complicated electrical power system with heightened levels of system sophistication and interdependence. These developments have the potential to drastically alter the solution space of all feasible aircraft Electrical Power System (EPS) designs. The technological advancements facilitating the MEA progression have allowed for a broader range of design solutions to exist that increase the size of the solution space. Meanwhile increasing system sophistication has led to an increasingly non-linear and complex solution space.

Advanced commercial aircraft increasingly use more composite or hybrid (metal and composite) materials in structural elements and, despite technological challenges to be overcome, composites remain the future of the aviation industry. Composite and hybrid aircraft today are equipped with digital systems such as fly by wire for reliable operations no matter what the flying environment is. These systems are however very sensitive to electromagnetic energy. During flight, aircraft can face High Intensity Radiated Fields (HIRF), static electricity, or lightning. The coupling of any of these threats with airframe structure induces electromagnetic energy that can impair the operation of avionics and navigation systems. This paper focuses on systems susceptibility in composite aircraft and concludes that the same electromagnetic rules dedicated to all metal aircraft for systems and wiring integration cannot be applied directly as such for composite aircraft.

Advanced technologies in LED's have the potential to reduce maintenance and improve aircraft safety. Aircrafts need adequate illumination for night time landing. New technology such as high-power LEDs allow for better suited light distributions, more whitish light compatible for mesopic lighting conditions and reduced glare in adverse weather conditions. LEDs and the associated electronics are more susceptible to harsh environmental conditions and this needs to be accounted for in the design of the equipment. Highly conductive metal core PCBs (MCPCB) allow for adequate cooling in a mirror telescopic optical arrangement when coupled with robust active cooling. Closed loop optical feedback of output flux ensures constant performance over the lifetime of the light unit and allows for indication of remaining useful life to the operator to plan maintenance activities. Parylene coating inhibits premature degradation of the LEDs induced by water vapor and corrosive gases.

The attributes of and challenges in the recently suggested probabilistic design for reliability (PDfR) concept, and the role of its major constituents - failure oriented accelerated testing (FOAT) and physically meaningful predictive modeling (PM) - are addressed, advanced and discussed. The emphasis is on the application of the powerful and flexible Boltzmann-Arrhenius-Zhurkov (BAZ) model, and particularly on its multi-parametric aspect. The model can be effectively used to analyze and design optoelectronic (OE) devices and systems with the predicted, quantified, assured, and, if appropriate and cost-effective, even maintained probability of failure in the field. The numerical example is carried out for an OE system subjected to the combined action of the ionizing radiation and elevated voltage as the major stimuli (stressors). The measured leakage current is used as a suitable characteristic of the degree of degradation.

An Airbus methodology for the assessment of accurate fuel pressure surge at early program stages in the complete aircraft and engine environment based on joint collaboration with LMS Engineering is presented. The aim is to comfort the prediction of the fuel pressure spike generated by an engine shutdown in order to avoid late airframe fuel system redesign and secure the aircraft entry-into-service.

Cost and performance requirements are driving military and commercial systems to highly integrated, optimized systems which require more sophisticated, highly complex controls. To realize benefits and make confident decisions, the validation of both plant and control models becomes critical. To quickly develop controls for these systems, it is beneficial to develop models and determine the uncertainty of those models so as to predict performance and stability. A process of model validation for a boost circuit based on acceptance sampling is presented here. The validation process described in this paper includes the steps of defining requirements, performing a screening and exploration of the system, completing a system and parameter identification, and finally executing a validation test. To minimize the cost of experimentation and simulation, design of experiments is used extensively to limit the amount of data taken without losing information.

In this paper we present a set of integrated circuits specifically designed for high temperature power applications such as isolated power transistor drivers and high efficiency power supplies. The XTR26010 is the key circuit for the isolated power gate drive application. The XTR26010 circuit has been designed with a high focus in offering a robust, reliable and efficient solution for driving a large variety of high-temperature, high-voltage, and high-efficiency power transistors (SiC, GaN, Si) existing in the market. The XTR40010 is used for isolated data communication between a microcontroller or a PWM controller and the power driver (XTR26010). The isolated power transistor driver features a dual turn-on channel, a turn-off channel and a Miller Clamp channel with more than 3A peak current drive strength for each channel. The dV/dt immunity between XTR26010 and XTR40010 exceeds 50kV/μs.

We have assembled and demonstrated a prototype power system that uses an innovative hydrogen generator to fuel an ultra-compact PEM fuel cell that is suitable for use in small unmanned aerial system (UAS) propulsion systems. The hydrogen generator uses thermal decomposition of ammonia borane (AB) to produce hydrogen from a very compact and lightweight package. An array of AB fuel pellets inside a low pressure container is activated sequentially to produce hydrogen on demand as it is consumed by the fuel cell. The fuel cell plant utilized in the power system prototype has been flown as part of several small UAS development programs and has logged hundreds of hours of flight time. The plant was designed specifically to be readily integrated with a range of hydrogen fueling subsystems and contains the balance of plant necessary to facilitate stand-alone operation. Based on results of these tests, we produced a conceptual design for a flight system.

A series hybrid-electric propulsion system has been designed for small rapid-response unmanned aircraft systems (UAS) with the goals of improving endurance, providing flexible and responsive electric propulsion, and enabling heavy fuel usage. The series hybrid architecture used a motor-driven propeller powered by a battery bank, which was recharged by an engine-driven generator, similar to other range-extended electric vehicles. The engine design focused on a custom, two-stroke, lean-burn, compression-ignition (CI), heavy-fuel engine, which was coupled with an integrated starter alternator (ISA) to provide electrical power. The heavy-fuel CI engine was designed for high power density, improved fuel efficiency, and compatibility with heavy fuels (e.g., diesel, JP-5, JP-8). Commercially available gasoline spark-ignition engines and heavy-fuel spark-ignition engines were also considered in the trade study.