Search Results

Flashing warning lights and vehicle markings of various colors are used on a wide range of emergency and other service vehicles to help inform drivers about the presence of these vehicles and the types of situations that drivers are approaching. Although not applied consistently among all jurisdictions, the colors and performance of these visual elements are often selected to help communicate the type of scenario (such as red flashing lights to indicate an emergency vehicle, or yellow flashing lights to indicate a non-emergency service vehicle). Previous investigations have shown that flashing light colors, vehicle and marking colors, and flashing temporal characteristics (e.g., rapid versus slower flashing) can all affect a driver’s perception of whether a vehicle along the road is responding to an emergency situation or not.

In the early stages of vehicle development, it is critical to establish performance goals for the major systems. The fundamental modes of body and chassis frames are typically assessed using FE models that are discretized using shell elements. However, the use of the shell-based FE method is problematic in terms of fast analysis and quick decision-making, especially during the concept phase of a vehicle design because it takes much time and effort for detailed modeling. To overcome this weakness, a one-dimensional (1D) method based on beam elements has been extensively studied over several decades, but it was not successful because of low accuracy for thin-walled beam structures. This investigation proposes a 1D method based on thin-walled beam theory with comparable accuracy to shell models. Most body pillars and chassis frame members are composed of thin-walled beam structures because of the high stiffness-to-mass ratio of thin-walled cross sections.

Certain sports utility vehicles (SUVs) utilize dual latches and gas struts in their hood design. This is primarily driven by the larger size of the hood and specific architectural requirements. These hoods can be securely latched either by a dynamic single stroke closing method or by quasistatic two stroke closing method. In dynamic method, the hood is closed with a single, high-velocity motion for the final primary latching, whereas in quasistatic method, force is initially applied for the secondary latching and then for the final primary latching. In this study, both the dynamic and quasistatic closing methods are compared in terms of closing force and velocity and hood over travel distance. A load cell is used for measuring the closing force, velocity meter is used for velocity measurement and a rope sensor is used for measuring the hood over travel distance.

Side doors are pivotal components of any vehicle, not only for their aesthetic and safety aspects but also due to their direct interaction with customers. Therefore, ensuring good structural performance of side doors is crucial, especially under various loading conditions during vehicle use. Among the vital performance criteria for door design, torsional stiffness plays an important role in ensuring an adequate life cycle of door. This paper focuses on investigating the impact of several door structural parameters on the torsional stiffness of side doors. These parameters include the positioning of the latch, the number of door side hinge mounting points on doors (single or double bolt), and the design of door inner panel with or without Tailor Welded Blank (TWB) construction.

Plastic design is one of the upcoming fields of interest when it comes to weight optimization, sustainability, strength, and overall aesthetics of an automobile. What is often ignored is the amount of flexibility a plastic designer has, of integrating and packaging various components of an automobile into a single part and still make it an integral part of its complex aesthetics. This paper highlights upon one such part that is being developed: An integrated bracket which packages ADAS camera, Rain Light Sensor, and an Auto-dimming IRVM. Apart from packaging the mentioned components, this bracket also has mounting provisions for an aesthetic cover (also referred to as beauty cover). The objective of this paper is to highlight the importance of integration of several parts into a single part for packaging multiple components that need to be placed in a close proximity with each other.

The recent surge in platforms like YouTube has facilitated greater access to information for consumers, and vehicles are no exception, so consumers are increasingly demanding of the quality of their vehicles. By the way, the door is composed of glass, moldings, and other parts that consumers can touch directly, and because it is a moving part, many quality issues arise. In particular, the door panel is assembled from all of the above-mentioned parts and thereby necessitates a robust structure. Therefore, this study focuses on the structural stiffness of the door inner panel module mounting area because the door module is closely to the glass raising and lowering, which is intrinsically linked to various quality issues.

A crucial component utilized in the trunk space is the luggage board. Positioned at the bottom of the trunk, the trunk board separates the vehicle body from the interior and supports for luggage. The luggage board serves multiple functions, including load-bearing stiffness for luggage, partition structure functionality, noise insulation, and thermal insulation. There is a need for a competitive new luggage board manufacturing method to meet the increasing demand for luggage boards in response to the changing market environment. To address this, the "integrated sandwich molding method" is required. The integrated sandwich molding method utilizes three key methodologies: grouping processes to integrate similar functions, analyzing materials to replace them with suitable alternatives, and overcoming any lacking functionality through integrated design structures. This paper presents a methodology for developing the integrated sandwich molding method.

The side-door operation of vehicle is vital to the customer, as it reflects the overall build quality of the vehicle. The side door check arm is one of the primary components that determine the operating characteristics of a vehicle door. The profile of the check arm has a significant impact on the closing effort of side doors. In this study, the check arm profiles are analyzed virtually in relation to the side door's closing velocity. A virtual door model was developed in ADAMS to simulate the side door closing and opening. The study involves a check arm that guides the ball spring mechanism housing unit over the guide profile. Typically, a check-arm guide profile has two or three indents at a specific location which serves to maintain the door open in those positions. When a door enters an indent, the user must exert an effort to traverse it. Furthermore, the slope profile of the check arm defines the self-closing assist offered from the initial indent to the latching position.

When designing an electric vehicle (EV) traction system, overcoming the issues arising from the variations in the battery voltage due to the state of charge (SoC) is critical, which otherwise can lead to a deterioration of the powertrain energy efficiency and overall drive performance. However, systems are typically documented under fixed voltage and temperature conditions, potentially lacking comprehensive specifications that account for these variations across the entire range of the vehicle operating regions. To tackle this challenge, this paper seeks to adjust an optimal DC-link voltage across the complete range of drive operating conditions by integrating a DC-DC converter into the powertrain, thereby enhancing powertrain efficiency. This involves conducting a comprehensive analysis of power losses in the power electronics of a connected converter-inverter system considering the temperature variations, along with machine losses, accounting for variable DC-link voltages.

The suspension system plays a crucial role in mitigating vehicle vibration, enhancing passenger comfort, and improving driving handling stability. While many mechanical experimental platforms exist for testing suspension system performance, they often need high costs and precision requirements. In the field of modern industrial product design, hardware-in-the-loop (HIL) simulation has become an invaluable tool. Electrically interconnected suspension (EIS) is a novel type of interconnected suspension by connecting various suspensions in an electrical way. The novel EIS avoids many drawbacks of traditional interconnected suspensions. The EIS is usually composed of electromagnetic motors and electrical networks (EN). By designing the structure of the EN reasonably, the EIS system can achieve decoupling control in multiple vibration modes. This paper introduces an HIL experimental platform established for a half-car EIS system based on an NI Compact RIO 9049.

This research focuses on the commercial 6111 aluminum alloy as the subject of investigation. By designing tensile specimens with the same characteristic dimensions but varying fillet radii, the effects of fillet radius on the tensile properties and stress concentration effects of the aluminum alloy were studied through tensile testing and digital image correlation techniques. The results demonstrate that with an increase in fillet radius, the failure strength and stress distribution of the aluminum alloy specimens have both undergone alterations. This phenomenon can be attributed to the reduction of stress concentration at the fillet due to the larger fillet radius. Further verification through digital image correlation reaffirms that samples with a fillet radius of 10mm exhibit notable stress concentration effects at the fillet, while specimens with a fillet radius increased to 40mm display uniform plastic deformation across the parallel section.

The significance of thermal management performance in electric vehicles (EVs) has grown considerably, leading to increased complexity in thermal systems and a rapid rise in safety and quality-related concerns. The present real-vehicle-based development methods encounter several constraints in their approach when dealing with highly complex systems. Huge number of verification and validation work To overcome these limitations and enhance the thermal system development process, a novel virtual development environment established using the XiLS (X in the Loop Simulation) methodology. This XiLS methodology basically based on real-time coupling between physical thermal system hardware and analytical models for the other systems of vehicle. To control vehicle model and thermal system, various options were realized through hardware, software and model for VCU (Vehicle control unit) and TMS (Thermal management system) control unit.

As the spread of electric vehicles increases, tests to measure the driving distance on a single charge, which takes about 6 hours or more to completely discharge the battery, have become necessary. There is also a need to conduct tests using indoor alternative modes, such as real driving emissions (RDE) tests, which take about two hours. These tests can be said to be very harsh working environments because they take long periods of time on chassis dynamometer, and sometimes low-temperature tests are also required. In this study, basic research was conducted to enable a driving robot to perform long-term automobile performance tests on behalf of humans indoors using a chassis dynamometer. The final development goal is to develop a driving pedal robot that has an automatic calibration function suitable for various vehicles and has a shorter installation time than driving robots in the existing market.

The EPB (Electric Parking Brake) system is divided into two parts based on VDA305-100 recommendation (German Association of the Automotive Industry, VDA). One part of the EPB system contains the parking brake actuator, caliper, and actuation logic (parking brake controller, PBC). The second part of the EPB system is called to the HOST which contains the EPB power electronics, necessary peripherals and controls the functions that the driver can experience. According to VDA305-100, the PBC is responsible for recognition of a fault in the parking brake actuator based on the measured values transmitted from the HOST such as EPB motor voltage and current. Due to mechanical fault injection limitations, failsafe tests require physically electrical emulation caused by parking brake actuator faults to verify the parking brake actuator fault detection and management algorithm.

Simulators are essential part of the development process of vehicles and their advanced functionalities. The combination of virtual simulator and Hardware-in-the-loop technology accelerates the integration and functional validation of ECUs and mechanical components. The aim of this research is to investigate the benefits that can arise from the coupling of a steering Hardware-in-the-loop simulator and an advanced multi-contact tire model, as opposed to the conventional single-contact tire model. On-track tests were executed to collect data necessary for tire modelling using an experimental vehicle equipped with wheel force transducer, to measure force and moments acting on tire contact patch. The steering wheel was instrumented with a torque sensor, while tie-rod axial forces were quantified using loadcells. The same test set has been replicated using the Hardware-in-the-loop simulator using both the single-contact and multi-contact tire model.

The piston and piston ring are used in a severe contact environment in engine durability tests, which causes severe wear to the piston ring groove, leading to significant development costs for countermeasures. Conventionally, in order to ensure functional feasibility through wear on the piston top ring groove (hereinafter “ring groove”), only functional evaluations through actual engine durability testing were performed, and there was an issue in determining the limit value for the actual amount of wear itself. Because of this, the mechanism that may cause wear on the ring groove was clarified through past research, but this resulted in judgment criteria with some leeway from the perspective of functional assurance. To establish judgment criteria, it was necessary to understand both functional effect from ring groove wear and the mechanism behind it.

As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty automotive technologies in support of regulatory and compliance programs, a development project was started to study various test methods to benchmark Electric Drive Units (EDUs) consisting of an electric motor, inverter and a speed-reduction gearset. Several test methods were identified for consideration, including both in-vehicle testing of the complete EDU and stand-alone testing of the EDU and its subcomponents after removal from the vehicle. In all test methods explored, sweeps of speed and torque test points were conducted while collecting key EDU data required to determine efficiency, including motor torque and speed, direct current (DC) battery voltage and current into the inverter, and three-phase alternating current (AC) phase voltages and currents out of the inverter and into the electric motor.

The flight mechanisms of birds have long inspired efforts to develop bioinspired aerial vehicles. This study presents a computational framework to analyze a flapping mechanism's structural behavior and performance based on the Scotch yoke principle. A three-dimensional CAD model is developed and meshed for finite element analysis in ANSYS. Structural steel is chosen as the material. Static analysis is performed under simulated flapping loads to predict deformation, stresses, fatigue life, and failure points. Preliminary results identify regions of high-stress concentration requiring optimization. Topology optimization is conducted to determine an optimal material layout within defined constraints. Additional shape and compliance optimizations are employed. Comparison of initial and optimized designs significantly reduces maximum deformation and stresses throughout the structure. Fatigue life and safety factors are markedly improved.

By introducing the yield strength ratio λ of strengthened ridgeline to plate and the strengthening coefficient multiplier R, the theoretical prediction expression of maximum bending moment of thin-walled square tube with strengthened ridgelines under static cantilever bending condition is obtained. Then the software of Hypermesh 13. 0 was used to establish two quasi-static finite element simulation comparison models under the corresponding static cantilever conditions. One model was designed for the original material thin-walled square tube, and another one was designed for the thin-walled square tube with strengthened ridgelines. After that, the LS-DYNA 971 solver was introduced to perform the solution calculations. Through a series of simulation calculations and result analysis, the accuracy of the theoretical expression for the maximum bending moment of a thin-walled square tube with strengthened ridgelines was verified.

The National Highway Traffic Safety Administration (NHTSA) plays a crucial role in guiding the formulation of Corporate Average Fuel Economy (CAFE) standards, and at the forefront of this regulatory process stands Argonne National Laboratory (Argonne). Argonne, a U.S. Department of Energy (DOE) research institution, has developed Autonomie—an advanced and comprehensive full-vehicle simulation tool that has solidified its status as an industry standard for evaluating vehicle performance, energy consumption, and the effectiveness of various technologies. Under the purview of an Inter-Agency Agreement (IAA), the DOE Argonne Site Office (ASO) and Argonne have assumed the responsibility of conducting full-vehicle simulations to support NHTSA's CAFE rulemaking initiatives. This paper introduces an innovative approach that hinges on a large-scale simulation process, encompassing standard regulatory driving cycles tailored to various vehicle classes and spanning diverse timeframes.