Search Results

Fuel consumption is the most important contributor to the total cost of ownership for mass produced motorcycles. Therefore, best fuel economy is one main influencing criteria for a decision to purchase motorcycles. Furthermore, increasingly stringent emission legislations limit and additional OBD requirements must be fulfilled. A new combined test approach has been developed that minimizes accuracy losses in the development process which compensates for the variability of driving behavior in the chassis dyno environment. An engine testbed combined with a belt drive transmission enables operation in single engine or in Powerpack (i.e. internal combustion engine including transmission) configuration as well as under steady state or dynamic operating mode. Since the belt drive transmission is integrated in the test rig, realistic inertia situation for the single engine operating test configuration is ensured.

This paper reviews psychophysiological measurement applied on humans, by mainly focusing on brain waves observed by EEG sensor placed on scalp during brake performance testing. During braking high physiological stress, response and fear are observed, hence brain waves are monitored during brake test. Brake performance by two drivers (i.e. Driver A & Driver B) significantly established the difference in brain potential between driver A &B. During the test, brake performance parameters such as vehicle speed, deceleration rate, brake force, stopping distance are also measured. Observed EEG signal during the braking event, revealed the difference in emotional status of two different drivers. Signal based on alpha and beta from brainwaves were evident to define the mental stability of the respective driver.

The paper describes theoretical and experimental method to calculate and measure Spark Energy and Spark Efficiency. Also the paper concludes the variable(s) affecting Spark Efficiency and Spark Energy. The new method adopted has an ascendancy over the existing methods, i.e., holographic interferometry and calorimetry, the new measurement method directly measures the energy in the two sparking regions, i.e., high current and low current region. Using this method it is possible to clearly identify the influencer and the significance of the two regions of sparking. The total energy delivered by the spark plug is majorly impacted by the low current region of sparking, and the high current region has minimal impact on the same. The tenor of results from new measurement method harmonizes with the test results from existing methods for certain variants such as gap and pressure, but it disaffirms in other variants such as electrode dimensions.

Rubber hose and metallic pipe with crimped joints are extensively used in steering system assembly, transmission oil cooler system, brake system etc. to carry hydraulic fluid or lubricants from one place to another. The pipe and rubber hose assembly provides necessary flexibility for complex routing on the vehicle level. Design of hose and pipe assembly for this application are different due to difference in operating pressure and temperature requirement for vehicle application. This paper defines the criteria for design and validation of hose & pipe assembly used to connect automatic transmission with the cooler. Crimped joints are validated for their separation force, leakages, ability to withstand pressure pulsations, burst test etc. Parameters which influence the hose & pipe assembly durability are pipe end flaring dimensions, type of crimping, reinforcement type, its size, material and pattern, rubber material properties, crimping force, effective crimping diameter etc.

Single plate dry clutch is one of the most abuse components in the vehicle. With the growing population of traffic in cities, useful life of clutch is affected drastically which is evident from the rise in complaints on clutch from metropolitan cities. The governing design parameter, which affects the life of clutch, is the energy dissipated in clutch per unit area of friction lining of clutch disc. The life of clutch is affected by many factors like vehicle weight, engine torque, driveline ratios, friction lining, size of clutch, which are taken into consideration during design stage of the clutch. Apart from these factors, one more factor, engine calibration, affects the clutch life drastically. However, it is not taken into consideration during design stage owing to its inherent nature as it gets matured over the vehicle development program.

Near-term advances in spark ignition (SI) engine technology (e.g., variable value lift [VVL], gasoline direct injection [GDI], cylinder deactivation, turbo downsizing) for passenger vehicles hold promise of delivering significant fuel savings for vehicles of the immediate future. Similarly, trends in transmissions indicate higher (8-speed, 9-speed) gear numbers, higher spans, and a focus on downspeeding to improve engine efficiency. Dual-clutch transmissions, which exhibit higher efficiency in lower gears, than the traditional automatics, and are being introduced in the light-duty vehicle segment worldwide. Another development requiring low investment and delivering immediate benefits has been the adaptation of start-stop (micro hybrids or idle engine stop technology) technology in vehicles today.

The Automotive Deployment Options Projection Tool (ADOPT) is a light-duty vehicle consumer choice and stock model supported by the U.S. Department of Energy's Vehicle Technologies Office. It estimates technology improvement impacts on future U.S. light-duty vehicles sales, petroleum use, and greenhouse gas emissions. ADOPT uses techniques from the multinomial logit method and the mixed logit method to estimate vehicle sales. Specifically, it estimate sales based on the weighted value of key attributes including vehicle price, fuel cost, acceleration, range and usable volume. The average importance of several attributes changes nonlinearly across its range and changes with income. For several attributes, a distribution of importance around the average value is used to represent consumer heterogeneity. The majority of existing vehicle makes, models, and trims are included to fully represent the market. The Corporate Average Fuel Economy regulations are enforced.

This paper investigates classifications of road type and driving style based on on-board diagnostic data, which is commonly accessible in modern vehicles. The outcomes of these classifications can be utilized in, for example, supporting the advanced driver assistance systems (ADAS) for enhancing safety and drivability, and online adaptation of engine controller for improving performance and fuel consumption. Furthermore, the classifications offer valuable information for fleet operators to consider when making decision on procurement plans, maintenance schedules and assisting fleet drivers in choosing suitable vehicles. To this end, a velocity-based road type classification method is evaluated on measurements collected from real driving conditions and compared to an open-sourced map. To produce representative results, two most commonly adopted driving style classification methods, i.e. acceleration and jerk-based methods are evaluated and compared on the same set of measurements.

This research presents the simulation of the jet behavior of gasoline ethanol blends in a quiescent chamber using the Lattice Boltzmann method. The fuel is taken as different mixtures of gasoline and ethanol, and the properties, such as density, viscosity and surface tension, are varied accordingly in the Lattice Boltzmann model. The variations in jet structure and instabilities are modeled according to the velocity of fuel injection, the composition of the gasoline-ethanol blend and the property of the surrounding mixture. The model implemented for the interaction of the two fluids; air and fuel, is the Shan Chen model. The accuracy of the model is confirmed using a static drop test at different curvatures for the two fluids as well as observing the evolution of merging droplets. This is the first time that the study of different fuels in done using the Shan Chen model.

A computational and experimental study was performed to characterize the flow within a gasoline injector and the ensuing sprays. The computations included the effects of turbulence, cavitation, flash-boiling, compressibility, and the presence of non-condensible gases. The flow domain corresponded to the Engine Combustion Network's Spray G, an eight-hole counterbore injector operating in a variety of conditions. First, a rate tube method was used to measure the rate of injection, which was then used to define inlet boundary conditions for simulation. Correspondingly, injection under submerged conditions was simulated for direct comparison with experimental measurements of discharge coefficient. Next, the internal flow and external spray into pressurized nitrogen were simulated under the base spray G conditions. Finally, injection under flashing conditions was simulated, where the ambient pressure was below the vapor pressure of the fuel.

The mixing field of sprays injected into high temperature and pressure environments has been observed to be tightly connected to spreading angle, therefore linking vaporization and combustion processes to the angular dispersion of the spray. Visualization of the Engine Combustion Network three-hole, Spray B diesel injector shows substantial variation in near-field spreading angle with respect to time compared to past measurements of the single-hole, Spray A injector. The source of these variations originating inside the nozzle, and the implications on mixing, evaporation, and combustion of the diesel plume, need to be understood. In this study, we characterize the ECN-target plume for a Spray B injector (Serial # 211201), which already benefits from extensive and detailed internal measurements of nozzle geometry and needle movement, while comparing to the single-hole Spray A with the same type of detailed geometry and understanding.

High-speed spray-to-spray liquid impingement could be an effective phenomenon for the spray propagation and droplet vaporization. To achieve higher vaporization efficiency, impingement from two-hole nozzles is analyzed in this paper. This paper focuses on investigating vaporization mechanism as a function of the impingement location and the collision breakup process provided by two-hole impinging jet nozzles. CFD (Computational Fluid Dynamics) is adopted to do simulation. Lagrangian model is used to predict jet-to-jet impingement and droplet breakup conditions while KH-RT breakup and O'Rourke collision models are implemented for the simulation. The paper includes three parts: First, a single spray injected into an initially quiescent constant volume chamber using the Lagrangian approach is simulated to identify the breakup region, which will be considered as a reference to study two-hole impinging jet nozzles. Lagrangian simulation results would be validated via experimental results.

The use of alcohols as alternative to gasoline for fuelling spark-ignition (SI) engines is widespread. Growing interest is paid for n-butanol because of its characteristics that are similar to gasoline. If compared with other alcohols, n-butanol has higher energy content and miscibility with gasoline, lower hygroscope and corrosive properties making it an attractive solution for gasoline replacement. Even if several studies have been conduced to characterize the n-butanol combustion within Spark Ignition engines, few data are available on atomization and spray behavior. This paper reports the results of an experimental investigation to characterize the velocity vector field of two fuel-sprays injected by a 6-hole nozzle for Direct Injection Spark Ignition (DISI) engine. 2D Mie-scattering and Particle Image Velocimetry (PIV) measurements were carried out in an optically accessible vessel at ambient temperature and pressure.

Comparing with port-fuel-injection (PFI) engine, the fuel sprays in spark-ignition direct-injection (SIDI) engines play more important roles since they significantly influence the combustion stability, engine efficiency as well as emission formations. In order to design higher efficiency and cleaner engines, further research is needed to understand and optimize the fuel spray atomization and vaporization. This paper investigates the atomization and evaporation of n-pentane, gasoline and surrogate fuels sprays under realistic SIDI engine conditions. An optical diagnostic technique combining high-speed Mie scattering and Schlieren imaging has been applied to study the characteristics of liquid and vapor phases inside a constant volume chamber under various operating conditions. The effects of ambient temperature, fuel temperature, and fuel type on spray atomization and vaporization are analyzed by quantitative comparisons of spray characteristics.

DiMethyl Ether (DME) has been known to be an outstanding fuel for combustion in diesel cycle engines for nearly twenty years. DME has a vapour pressure of approximately 0.5MPa at ambient temperature (293K), thus it requires pressurized fuel systems to keep it in liquid state which are similar to those for Liquefied Petroleum Gas (mixtures of propane and butane). The high vapour pressure of DME permits the possibility to optimize the fuel injection characteristic of direct injection diesel engines in order to achieve a fast evaporation and mixing with the charged gas in the combustion chamber, even at moderate fuel injection pressures. To understand the interrelation between the fuel flow inside the nozzle spray holes tests were carried out using 2D optically accessed nozzles coupled with modelling approaches for the fuel flow, cavitation, evaporation and the gas dynamics of 2-phase (liquid and gas) flows.

Time-resolved mass injection rates of an outward opening piezo-actuated and a solenoid actuated multi-hole GDI injector were measured to investigate (1) the influence of both hardware and software settings and (2) the influence on the injection rates from a wide range of operational parameters and (3) discuss limitations and issues with this measurement technique. The varied operating parameters were fuel pressure, back-pressure, electrical pulse width, single/double injection and injection frequency. The varied hardware/software parameters were injector protrusion, upstream fuel pressure condition and the cut-off frequency of the software's low-pass filter. Signal quality was found to be dependent on both hardware and software settings, especially the cut-off frequency of the low-pass filter. Measurements with high signal quality were not possible for back-pressures lower than 0.5 MPa.

Understanding the physics and chemistry involved in diesel combustion, with its transient effects and the inhomogeneity of spray combustion is quite challenging. Great insight into the physics of the problem can be obtained when an in-cylinder computational analysis is used in conjunction with either an experimental program or through published experimental data. The main area to be investigated to obtain good combustion begins with the fuel injection process and the mean diameter of the fuel particle, injection pressure, drag coefficient, rate shaping etc. must be defined correctly. The increased NOx production and reduced power output found in engines running biodiesel in comparison to petrodiesel is believed to be related to the different fuel characteristics in comparison to petroleum based diesel. The fuel spray for biodiesel penetrates farther into the cylinder with a smaller cone angle. Also the fuel properties between biodiesel and petrodiesel are markedly different.

In a direct injection gasoline engine, the impingement of injected fuel on the oil film, i.e. cylinder liner gives rise to various problems such as abnormal combustion, oil dilution and particulate matter emission. Therefore, in order to solve these problems, it is necessary to have a clear understanding of the impingement behavior of the fuel spray onto the oil film. However, there is little information on the impingement behavior of the fuel droplet onto the oil film, whereas many investigations on the impingement behavior of the fuel droplet onto the fuel film are reported. In this study, fundamental investigations were performed for the purpose of clarifying the impingement behavior of the fuel spray onto the oil film. A single fuel droplet mixed with fluorescence dye was dripped on the oil film. To separately measure the fuel and the oil after impingement, simultaneous Mie scattering and laser-induced fluorescence (LIF) methods were performed.

The work analyses, from both an experimental and a numerical point of view, the impingement of a spray generated from a GDI injector on a hot solid wall. The temperature of the surface is identified as an important parameter affecting the outcome after impact. A gasoline spray issuing from a customized single-hole injector is characterized in a quiescent optically-accessible vessel as it impacts on an aluminum plate placed at 22.5 mm from the injector tip. Optical investigations are carried out at atmospheric back-pressure by a direct schlieren optical set-up using a LED as light source. A synchronized C-Mos high-speed camera captures cycle-resolved images of the evolving impact. The spatial and temporal evolution of the liquid and vapor phases are derived. They serve to define a data base to be used for the validation of a properly formulated 3D CFD model suitable to describe the impact of the fuel on the piston head in a real engine.

In direct-injection engines, combustion and emission formation is strongly affected by injection quality. Injection quality is related to mass-flow rate shape, momentum rate shape, stability of pulses as well as mechanical and hydraulic delays associated with fuel injection. Finding these injector characteristics aids the interpretation of engine experiments and design of new injection strategies. The goal of this study is to investigate the rate of momentum for the single and post injections for high-pressure direct-injection natural gas injectors. The momentum measurement method has been used before to study momentum rate of injection for single and split injections for diesel sprays. In this paper, a method of momentum measurement for gas injections is developed in order to present transient momentum rate shape during injection timing. In this method, a gas jet impinges perpendicularly on a pressure transducer surface.