Search Results

In order to achieve lean burn engine control system, it is necessary to develop high accuracy air fuel ratio control technology including transient driving condition and lean burn limit expansion technology. This paper describes the following. 1 The characteristics of the transient response of the fuel supply are clarified when various kinds of air flow measuring methods and fuel injection methods are used. 2 To achieve stable combustion in lean mixture, fine fuel droplet mixture, whose diameter is less than 40 μm, needs to be supplied.

Unsteady laminar flame propagation confined in a closed cylindrical combustion bomb is studied by numerical computation for an axisymmetric two-dimensional laminar flame. Computation includes complete two-dimensional unsteady Navier-Stokes equations of change for a chemically reacting propane-air mixture. Implicit Continuous fluid Eulerian, Arbitrary Lagrangian Eulerian finite difference technique, simplified reaction kinetics models, and artificial flame stretching transformation and inverse transformation were adopted in the calculation. Physically realistic flame behavior can be demonstrated even with rather coarse computing cell size, simplified reaction kinetics models, and personal computer level low power computing machines.

A procedure has been developed for evaluating equivalent drive cycle emission results from raw exhaust gas emissions data obtained from an engine under test on a computer controlled Vehicle Simulator Engine Dynamometer. The emitted species data is integrated with the air intake flow rate to determine the total mass of emissions, after correcting for the reduction in exhaust gas mass due to precipitation of the moisture of combustion. This procedure eliminates the need for the Constant Volume Sample (CVS) System attached to the vehicle exhaust while undergoing simulated drive testing on a chassis dynamometer to evaluate compliance of the test vehicle with the Australian Design Rules, ADR27 and ADR37. Sources of error with the procedure are examined by comparing the fuel consumption measured using a volumetric technique during the test with that evaluated by a carbon balance procedure as given in the Australian Design Rules.

An all-ceramic swirl chamber has been developed and analyses and evaluations concerning the strength of silicon nitride ceramic (Si3N4) have been performed with a view to using it for the entire internal wall surface of the swirl chamber. The strength characteristics of Si3N4 and their effect and variation have been determined. On the basis of measurements and analyses of thermal stresses, assembling stresses, etc., investigation of the most suitable construction and assembling methods to reduce load stresses on ceramic, and various kinds of duration tests, the swirl chamber has been confirmed to have the required durability. This engine was found to comply with the 1987 U.S. diesel particulate regulation.

The sequential fuel injection, in which fuel is injected into swirl being generated for mixture stratification, was used to pursue the potential of a lean burn engine for its performance improvement. As a result, it has been found that the most effective method to increase thermal efficiency while reducing NOx emission level is to combine a high-compression compact combustion chamber located on exhaust valve side in cylinder head with DICS (Dual induction Control System). This method was used to build a high-compression lean burn concept vehicle, which was evaluated for compliance to various emission standards. Testing showed that the concept vehicle can improve fuel economy by 10.5% on the Japanese 10-mode cycle, by 8.3% on the ECE mode cycle, and by 6.3% on the U.S. EPA test mode cycle while meeting respective emission standards.

For the purpose of satisfying today's market demands, new 8 and 11 liter diesel engines, named "STORM" series, have been developed and moved into production in 1986. Based on the predecessors which have been produced since 1975, the development of the STORM series aimed high performance, low emission, long life-time and low operating costs. In order to consult customers' convenience, exchangeability of engine parts and commonality of vehicle installations with the former engines had to be maintained. This paper describes the development work of STORM engines, and the design aspects and performance characteristics of these engines.

CORRELATION OF BENDING STRENGTH AND ERRORS OF HELICAL GEAR has not been clarified sufficiently even now. As the investigation by using only experimental method is not sufficient and so the analytical method of obtaining gear bending strength has been developed by one of the authors. Hence, the correlation of bending strength and errors, especially in the aspect of the direction of pressure angle error and tooth trace error, is clarified by this analytical method which was verified by some experiments. And by further investigations, it is confirmed that the helical gear is tougher against the negative pressure angle error, and the fine module gear is sensitive against the errors.

In this paper a computer simulation study on the effects of steering parameters on lateral dynamics of the guideway bus to contribute to a development practice of designing optimum steering control system are dealt with. A stability limit of vehicle lateral motion is analyzed and an emphasis is laid on the effects of moment of inertia of a conventional steering wheel and lateral elasticity of the guide rail which have proven to reduce the critical vehicle speed. It is pointed out conclusively that a normal bus equipped with additional simple guidance equipments can be guided smoothly on a simple guideway at adequately high vehicle speed.

The influence of the tyre properties on the driving behaviour of single-track vehicles has been measured by performing running tests with full-scale vehicles. The indoor dynamic tyre measurements using the sideslip angle as the input signal reveale that the sideforce and self-aligning moment characteristics are helpful explaining the measured driving behaviour. The obtained tyre parameters values and second order equations have been implemented in the simulation program ADINA-MOBSIP. This program is specially conceived for the simulation of the driving behaviour of single-track vehicles and is based on the finite element method.