Search Results

In the design and development of modern cars with respect to comfort, silence and safety, state of the art experimental modal analysis is one of the essential development tools. Due to the large amount of degrees of freedom of such a large and complex system like a car with all its components, a complete simulation by FEM can not be realised easily and requires an enormous expenditure of work and calculations. In addition the simulations are based on assumed system parameters and thus the vibration behaviour of the resulting prototypes often is not completely identical to the simulated model. In contrast to conventional measurements with accelerometers, the 3-D Scanning Vibrometer enables fast and efficient non-contact measurements of the in-plane and out-of-plane vibration behaviour at all optical accessible surfaces. The method easily allows to increase the number of measured points to obtain a high measurement point density.

3-D shell components are used intensively in the automotive industry. Many structural topology optimization techniques were developed to reduced the total weight of shell structures while retaining its structural performance. One common approach is to utilize the concept of the design domain, such as the homogenization method and the density function approach. In this paper, a new micro-structure based design domain method is introduced to solve 3-D shell topology optimization problems. Based on physical micro-structure model, simple closed-form expressions for effective Young's modulus and effective shear modulus are rigorously derived. Using these simple relations, topology optimization problems can be formulated and solved with sequential convex approximation algorithms. Two design examples obtained from the new method are presented.

A three-dimensional model is used to compute the flow,sprays and combustion in a stratified-charge rotary engine. Wall temperatures estimated from available measurements are used as boundary conditions for the energy equation. The computations provide local and instantaneous heat fluxes on the rotor and the rotor housing. The instantaneous heat fluxes are integrated in time over one cycle of the rotor to obtain estimates of local cycle averaged heat flux through the rotor and the rotor housing. These are then used as boundary conditions in a thermal analysis of the rotor and rotor housing with known coolant-side flow rates and heat transfer coefficients. The thermal analysis is done using a finite-element three-dimensional code which provides updated estimates of the rotor and rotor housing wall temperatures. These wall temperatures agree within ±20°C of the measured wall temperatures.

A displacement based finite element model is developed to predict 3-D thermal stress induced by high temperature and temperature gradient during diesel particulate filter (DPF) regeneration. The temperature field predicted by 3-D conservation of energy is used as input. This finite element model is self-contained and independent of commercial package. It includes functions of meshing body, assembling global stiffness matrix and force vector, solving final equilibrium equations as well as post-processing. This model is validated by commercial software ANSYS and good agreement is observed. Typically, it is the peak temperature rather than temperature gradients that lead to maximum compressive thermal stress in DPF during regeneration. The maximum stress always appears at the channel corner located at the end of DPF. Parametric studies of DPF during loading and regeneration as well as the effect of particulate loading on thermal stress during regeneration are carried out.

A 3-D video sensor designed for in-vehicle operation is presented in this paper. This sensor enables improved occupant protection according to the Federal Motor Vehicle Safety Standard (FMVSS) 208 and beyond. Interior sensors integrated in current occupant protection systems are especially designed for Occupant Classification (OC). However, these interior sensors do not measure the distance between the head and the air bag module. As a result, the air bags deploy independently from the occupants' Out-Of-Position (OOP) status in crash situations. On the contrary, the sensor presented in this paper overcomes this shortcoming by providing dynamic Out-Of-Position Sensing (OOPS) capabilities in addition to occupant classification. The requirements of dynamic OOPS are discussed and an appropriate test device and test procedure are described. Furthermore, the paper presents the sensor principle, the hardware architecture and algorithms for image data processing.

During sheet metal forming processes, the friction conditions have a decisive influence on forming limits, the robustness of the production process and the quality of the parts produced, with significant forces required to overcome friction between the sheet and the tools. If lot-to-lot reproducibility is to be guaranteed, an appropriate method of characterizing the sheet surface topography is needed to monitor the sheet metal fabrication process. Newly developed optical measurement techniques and computer workstation technology are presented which enable the topography of sheet surfaces to be described in three dimensions.

In order to use modeling as a predictive tool for real-world particulate filter designs (segmented filters, non-axisymmetric designs), it is necessary to develop reliable 3-dimensional models. This paper presents a 3 d modeling approach, which is validated against engine-bench measurements with both FBC and CDPF systems. Special emphasis is given to the prediction of the transient inlet flow distribution, which is realized without resorting to external CFD software. The experimental and modeling results illustrate the 3-d nature of the problem, induced by the heat capacity and conductivity effects of the cement layers. It is possible to predict the localization of regeneration in certain areas of the filter (partial regeneration), as a result of poor heat transfer to thermally isolated regions in the filter. The accuracy of the model was validated by extensive comparisons with temperature measurements in 30 positions inside the filters and at various operating conditions.

Exhaust gas recirculation technology is one of the main methods to reduce engine emissions. The pressure of the intake pipe of turbocharged direct-injection diesel engine is high, and it is difficult to realize EGR technology. The application of Venturi tube can easily solve this problem. In this paper, the working principle of guide-injection Venturi tube is introduced, the EGR system and structure of a turbocharged diesel engine using the guide-injection Venturi tube are studied. According to the working principle of EGR system of turbocharged diesel engine, the model of guide-injection Venturi tube is established, the calculation grid is divided, and it is carried out by using Computational Fluid Dynamics method that the three-dimensional numerical simulation of the internal flow of Venturi tube under different EGR rates injection.

CuO-water nanofluids was utilized as heat transfer medium in the cooling system of the diesel engine. By using CFD-Fluent software, for 0.5%, 1%, 3% and 5% mass concentration of nanofluids, 3-dimensional numerical simulation about flow and heat transfer process in the cooling system of engine was actualized. According to stochastic particle tracking in turbulent flow, for solid-liquid two phase flow discrete phase, the moving track of nanoparticles was traced. By this way, for CuO nanoparticles of different mass concentration nanofliuds in the cooling jacket of diesel engine, the results of the concentration distribution, velocity distribution, internal energy variation, resident time, total heat transfer and variation of total pressure reduction between inlet and outlet were ascertained.

Sudden tire deflation, or blow-out, is sometimes cited as the cause of a crash. Safety researchers have previously attempted to study the loss of vehicle control resulting from a blow-out with some success using computer simulation. However, the simplified models used in these studies did little to expose the true transient nature of the handling problem created by a blown tire. New developments in vehicle simulation technology have made possible the detailed analysis of transient vehicle behavior during and after a blow-out. This paper presents the results of an experimental blow-out study with a comparison to computer simulations. In the experiments, a vehicle was driven under steady state conditions and a blow-out was induced at the right rear tire. Various driver steering and braking inputs were attempted, and the vehicle response was recorded. These events were then simulated using EDVSM. A comparison between experimental and simulated results is presented.

The design of engine intake system affects the intake uniformity of each cylinder of the engine, which in turn has an important impact on the engine performance, the uniform distribution of EGR exhaust gas and the combustion process of each cylinder. In this paper, the constant-pressure supercharged diesel engine intake pipe is used as the research model to study the intake air flow unevenness of the intake pipe of the supercharged diesel engine. The pressure boundary condition at the outlet of each intake manifold is set as the dynamic pressure change condition. The three-dimensional numerical simulation of the transient flow process in the intake manifold of diesel engine is simulated and analyzed by using numerical method, and the change of the Intake air flow field in the intake manifold under different working conditions during the intake overlapping period is discussed.

Three-dimensional transient simulation was performed and an autoignition model was implemented to predict knock occurrence and autoignition site in a heavy-duty liquefied petroleum gas (LPG) engine. A flame area evolution (FAE) premixed combustion model was applied to simulate flame propagation. Engine experiments using a single-cylinder research engine were performed to calibrate the reduced kinetic model and to verify the result of this modeling. A pressure transducer and a head-gasket type ion-probe circuit board were installed to detect knock occurrence, flame arrival angle, and autoignition site. The simulation result shows good agreement with engine experiments. It also provides much information about in-cylinder phenomena and some ways to reduce knocking tendency. This knock simulation can be used as a development tool of engine design.

A new lightweight gasoline, two-cycle engine for portable tools is described. The total weight of 8 lb with an output of 3.5 hp was achieved by means of compact design with the use of standardized parts wherever possible, rather than by creating all new parts.

The switched reluctance generator, because of its simple and robust structure, is attractive as an auxiliary power unit (APU) in lightweight, high-speed and high power military, and other types of vehicles. In this paper, investigation and design analysis of a 300 kW switched reluctance generator is presented. Five different designs of the machine are evaluated to provide 300 kW at 30,000 rpm, 60,000 rpm, and at 100,000 rpm. The different designs are compared in terms of size, weight, efficiency, and torque. Analyses of the mechanical stress and critical speeds are also presented. Recommendations are presented for the selection of the best design methodology for APU application in Hybrid vehicles.

To meet the demands of continually increasing energy requirements, the off-shore operations to explore and recover petroleum deposits from beneath the ocean bottom are taking place under increasingly difficult environmental conditions. This has led to the development of types of equipment well beyond the possibilities or the imaginable future requirements of twenty years ago. When conditions require the fabrication of off-shore platforms on land, to be floated to the erection site, lifted and placed as a single unit of up to 3000 tons, revolving cranes capable of performing such lifts become a necessary part of that development.

Examining the noise reduction of a motorcycle, the requirement of an effective method of reducing a drive chain noise has been a pending issue similarly to noise originating from an engine or exhaust system, etc. Through this study, it became clear that the mechanism of chain noise could be classified into two; low frequency noise originated from cordal action according to the degree of chain engagement and high frequency noise generated by impact when a chain roller hits sprocket bottom. An improvement of urethane resin damper shape, mounted on a drive side sprocket, was effective for noise reduction of the former while our development of a chain drive that combined an additional urethane resin roller with an iron roller worked well for the latter. The new chain system that combined this new idea has been proven to be capable of reducing the chain noise to half compared with a conventional system.

This project is an experimental investigation and optimization of piston slap noise in small two-stroke gasoline engine. Piston slap is one of the most significant mechanical noise sources in an internal combustion engine. It is a dynamic impact phenomenon between the piston and the cylinder block caused by changes in the lateral forces acting on the piston. The change in cylinder block vibration level caused by the piston impact is considered as a measure of piston slap during this experiment. The intensity of piston slap is measured in terms of vibration level in ‘g’ units, by means of accelerometers mounted on the cylinder block with Top Dead Center (TDC) and Bottom Dead Center (BDC) marker. For the design of low noise engines, all the major parameters, which contribute to piston slap, are listed and the critical four are examined through additional experiments.

In the research of DME compression ignition engine, there are a lot of reports on the high fuel pressure systems which are used in the common-rail fuel injector and others for the DME mixture formation promotion. However, the initial development-cost of these fuel supply systems will be increased for small compression ignition engines. On the other hand, it has been understood that excellent thermal efficiency of DME compression ignition engine was obtained at the appropriate fuel injection timing by using the electronic controlled injector with low pressure injection. In this paper, the stabilization of combustion on DME compression ignition engine with low pressure injection was investigated for the influence of the fuel pressure and the combustion assistance with homogeneous charge.