Search Results

Many applications of liquefied petroleum gas (LPG) to commercial vehicles have used their corresponding diesel engine counterparts for their basic architecture. Here a review is made of the application to commercial vehicle operation of a robust 4 L, light-duty, 6-cylinder in-line engine produced by Ford Australia on a unique long-term production line. Since 2000 it has had a dedicated LPG pick-up truck and cab-chassis variant. A sequence of research programs has focused on optimizing this engine for low carbon dioxide (CO₂) emissions. Best results (from steady state engine maps) suggest reductions in CO₂ emissions of over 30% are possible in New European Drive Cycle (NEDC) light-duty tests compared with the base gasoline engine counterpart. This has been achieved through increasing compression ratio to 12, running lean burn (to λ = 1.6) and careful study (through CFD and bench tests) of the injected LPG-air mixing system.

The engine designer has to find novel methods to optimize the engine efficiency faster as the engine development cycle is getting shortened due to the continuous growing market demands. Engine optimization involves fine tuning of the various engine parameters and conducting a large number of tests on actual engine test bed. In this paper, modern techniques that have been used to optimize a small 4stroke air-cooled engine performance have been described. The engine has been modelled using one-dimensional thermodynamic engine modelling software (AVL-BOOST). Design of experiments (DoE) tools have been used to optimize the engine variables. The input parameters form an orthogonal array of L27 matrix and the out put characteristics of the engine (responses) have been predicted by using BOOST software. This design matrix has been used to study and optimize thirteen factors in three levels (313).

This paper presents results of an analytical comparison between two alternative versions of a crankshaft for a 2.2L gasoline engine. The first version had 8 counterweights and a bay balance factor of 80.3%. The second had 4 (larger) counterweights giving a bay balance factor of 56.6% and a crankshaft mass reduction of 1.42 kg. The results presented in this paper relate to the main bearings in terms of specific loads, oil film thickness and shaft tilt angle under full load and no load conditions across the speed range. Torsional vibration analysis and crankshaft stress analysis were also performed but the results are not presented here. The differences in bearing force and oil film thickness were very small and the only major difference in terms of shaft tilt angle occurred at Mains 2 and 4 (increase of ∼ 20% compared with 8 counterweight version).

The authors have published SAE paper 2008-01-0088 on the analytical comparison between 4 and 8 counterweight crankshafts for an I4 gasoline engine. This paper showed that for a particular design of a 4 counterweight crankshaft, the differences in bearing force and oil film thickness were very small and the only major difference in terms of bearing shaft tilt angle occurred at mains 2 and 4 (increase of ∼20% compared with 8 counterweight version). The 4 counterweight crankshaft has a significant mass advantage as it was 1.42kg lighter than the 8 counterweight crankshaft. This new paper addresses the testing performed to validate the analysis results in bearing durability by subjecting the engine to a mixture of high speed and general durability cycles. A comparison was made on the bearing conditions after running a total of 100 hours through prescribed durability cycles on a gasoline engine with both 4 and 8 counterweight crankshafts.

Ride quality is one of the most important criteria by which people judge the design of a car. At the most basic level, ride isolation properties are investigated using a quarter vehicle model. But the input from road roughness would excite not only bounce motions, but also pitch motions. Understanding the pitch and bounce motions is essential because it is their combination that determines the vertical and longitudinal vibrations at any point on the vehicle [2]. In this paper, a 4-degree-of-freedom (4-DOF) Vehicle Ride Model, which is shown in Figure 1, is used to investigate the effect on the ride quality of the dynamic index in pitch, mass ratio, weight distribution and flat ride tuning. A Lagrange equation is used to derive the equations of motion. A state-space formulation is obtained by using state variables. From these, the characteristic equation, natural frequency and damping ratio are obtained.

The possibility of 2 Channel anti-lock system, which controls each of two independent hydraulic circuits of diagonal split braking system of FWD car seperately, were studied. Theoretical investigation suggested two out of four possible control logics to be promising and they were proved to be practically satisfactory through vehicle test. This system is almost as effective as expensive 3-channel or 4-channel system, when the braking force distribution between front and rear axles is correct as required by EEC Braking regulation. Under extreme condition that rear wheels lock earlier than fronts, the compromise between stopping distance and stability is necessary.

Controlled Auto-Ignition (CAI) also known as Homogeneous Charge Compression Ignition (HCCI) is increasingly seen as a very effective way of lowering both fuel consumption and emissions. Hence, it is regarded as one of the best ways to meet stringent future emissions legislation. It has however, still many problems to overcome, such as limited operating range. This combustion concept was achieved in a production type, 4-cylinder gasoline engine, in two separated tests: naturally aspirated and turbocharged. Very few modifications to the original engine were needed. These consisted basically of a new set of camshafts for the naturally aspirated test and new camshafts plus turbocharger for the test with forced induction. After previous experiments with naturally aspirated CAI operation, it was decided to investigate the capability of turbocharging for extended CAI load and speed range.

Today's agri-businessman is challenged to improve his efficiency to meet higher operating costs and to counter the effects of inflation. New concepts in John Deere's line of 4-wheel-drive tractors are targeted toward this goal and provide increased productivity through power increases, improved fuel economy, comfortable convenient operator environment and controls, increased hydraulic power, improved serviceability and repairability and monitoring of more critical vehicle functions.

Last year, Southern Pacific Co. took delivery of three 4000 hp diesel-hydraulic locomotive units built in Germany to meet the rigorous requirements of United States railroad service. These experimental units incorporate a propulsion system not currently available in the United States and represent the highest output diesel locomotive units yet constructed. The prototypes are being road tested in heavy duty mountain freight service and expedited freight service to develop their potential under operating conditions here. The paper covers fundamentals of diesel-hydraulic design, some interesting engineering features incorporated in these units, and the test program being conducted to develop the potentialities of this design under service conditions.

Starting with the laboratory study, the amount of exhaust emission compound dissolved in water was measured, and the divergence of exhaust emission compounds was reviewed. Measurements were taken for hydrocarbon (HC), especially benzene, toluene, m-Xylene, p-Xylene, and o-Xylene. It was verified that the amount of exhaust emission compounds dissolved in water has positive correlation with the volume of exhaust gas introduced into the water. The dissolved amount was smaller with the low emission engine model. Volatile Organic Compound (VOC) decreased sharply at the beginning, but the decrement got smaller after a certain period of time. Next research was performed on the actual river where PWC are being used. We looked into the possible correlation between the VOC's concentration in water and the distance to the water where a lot of PWC's are running. In addition the MTBE (Methyl Tertiary-Butyl Ether) concentration was measured.

A 2001 General Motors 4.3 liter V-6 marine engine was baseline emissions tested and then equipped with catalysts. Emission reduction effects of exhaust gas recirculation (EGR) were also explored. Because of a U.S. Coast Guard requirement that inboard engine surface temperatures be kept below 200°F, the engine's exhaust system, including the catalysts, was water-cooled. Engine emissions were measured using the ISO-8178-E4 5-mode steady-state test for recreational marine engines. In baseline configuration, the engine produced 16.6 g HC+NOx/kW-hr, and 111 g CO/kW-hr. In closed-loop control with catalysts, HC+NOx emissions were reduced by 75 percent to 4.1 g/kW-hr, and CO emissions were reduced by 36 percent to 70 g/kW-hr of CO. The catalyzed engine was then installed in a Sea Ray 190 boat, and tested for water reversion on both fresh and salt water using National Marine Manufacturers Association procedures.

Electrical Air Conditioning Systems for 42 V vehicles will provide many benefits in terms of Environment protection, car Architecture, cabin Comfort and overall Safety. E-A/C Systems essentially differ from conventional ones by the use of electrical compressors. First of all, they will be particularly well adapted to new powertrains, helping to make them more environmentally friendly. Accurate control and high efficiency under the most common thermal conditions will reduce the A/C impact on fuel consumption. Besides, higher sealing integrity will cut emissions of refrigerant during normal operation and maintenance. Secondly, the use of an electrically driven compressor (EDC) will suppress a belt, and will reduce the packaging constraints. This will help to design new vehicle architectures. Thirdly, the electrification of air conditioning will allow better thermal comfort. In particular, E-A/C Systems provide a good opportunity for cabin pre-conditioning.

The 42-Volt electrical system is being introduced in automobiles to provide the extra power needed for various electromagnetic devices. These paper discuses the opportunity offered by the 42Volt for powder metal parts and the challenges. Major opportunities are in motors. A brief discussion of motors and the performance requirements for the magnetic core material used is included. Brushless motor design can benefit the most from insulated iron powder compacts because of the design simplicity of powder metal parts and three dimensional flux capability which is most beneficial in rotating devices.(P/M stands for powder metallurgy and not permanent magnets)

The growing electrical power demands on bus electrical systems, such as the electric door operator, power steering, braking, air conditioning, windshield wipers, seat heating, and the need to improve emissions and fuel economy, are making current 12/24-volt electrical systems inadequate. For buses to continue to meet growing customer needs, electrical power must be increased. The industry is currently pursuing a 42-volt system as standard. In the U.S., that number (42 volts) was selected by an industry-wide research consortium led by the Massachusetts Institute of Technology. The switch to a 42-volt system would revolutionize the automotive industry. This would enable more electronic components and new technologies to be added to the vehicle. At the present time, the discussion and implementation of the 42-volt system is largely on luxury vehicles. The potential benefit of the system on heavy duty vehicles has not been fully explored.

A few years ago, the automobile industry agreed to adopt standards for a new voltage for the production and use of electrical power. The perception was near universal that 14 Volts was at the limits of its capability, and that 42 Volts would be adopted in a rush. The universal perception was wrong. Since then, much of the auto industry has encountered hard financial times. In a totally separate development, parts suppliers introduced innovations at 14 Volts, some of which a few years ago were thought to require 42 Volts. Today, there are 42-Volt cars and trucks for sale, but only at numbers far lower than necessary to begin to achieve economies of scale. But the factor which caused the industry to develop the 42 Volt standard, the growth of electricity use on motor vehicles, continues with no sign of letup. Further, the true technical obstacles to adoption of 42 Volts have been discovered and at least provisionally solved.

The electrification of accessories using a fuel cell as an auxiliary power unit reduces the load on the engine and provides opportunities to increase propulsion performance or reduce engine displacement. The SunLine™ Class 8 tractor electric accessory integration project is a United States Army National Automotive Center (NAC™) initiative in partnership with Cummins Inc., Dynetek™ Industries Ltd., General Dynamics C4 Systems, Acumentrics™ Corporation, Michelin North America, Engineered Machine Products (EMP™), Peterbilt™ Motors Company, Modine™ Manufacturing and Masterflux™. Southwest Research Institute is the technical integration contractor to SunLine™ Services Group. In this paper the SunLine™ tractor electric Air Conditioning (AC) system is described and the installation of components on the tractor is illustrated. The AC system has been designed to retrofit into an existing automotive system and every effort was made to maintain OEM components whenever modifications were made.

A new electronically controlled transaxle has been put into production for Chrysler's family of LH cars. Among the attributes of this new transaxle are its ability to handle engines of high torque and high power coupled with high-speed shifts. Engine torque management is used in specific operating regimes. A feature of the transaxle is electronic modulation of the converter clutch. A number of logic features have been combined with hardware to provide good performance and shift quality over a wide operating range. An output transfer chain and a hypoid gear set are used to provide torque to the front wheels in a longitudinal power train orientation. Obtaining acceptable endurance life of the hypoid gears within an aluminum housing presented a significant challenge. New approaches were required to provide a chain-sprocket system with acceptable noise characteristics.

With the increase of hotel and ancillary loads and replacement of engine driven mechanical and hydraulic loads with electrical loads, automotive systems are becoming more electric. This is the concept of More Electric Cars (MEC) that necessitates a higher system voltage, such as the proposed 42V, for conventional cars. In this paper, the development of the 42V electric power system for vehicle applications is reviewed. The system architecture and motor drive problems associated with the 42V electric power system are analyzed. Solutions to these problems are also discussed.

Demands for new features, increasing electrical loads, and improved fuel-economy are driving development of 42V PowerNets in automobiles. Shorter design cycles, increased complexity and a focus on quality are making robust design processes a strategic advantage for competitive manufacturers. Hardware prototypes are both time-consuming and inadequate for the task of verifying performance over a broad range of operating modes, environmental conditions and part-to-part variations. This paper outlines the use of an advanced design-flow, from idea to manufacturing, for vehicle power systems. It starts with the analysis of different topologies down to the subsystem modeling of a power window system. Finally it integrates everything to a Digital Mock-Up (DMU) and analysis of the entire system. Dynamic interactions among the various supplies, converters and loads are examined. System stability and performance are assessed under normal and extreme operating conditions.

The increasing power demand in vehicles has resulted in a need for a higher onboard generation capacity. With the increasing generation requirement, the torque levels of the generator are found to closely converge with that of the starter motor. Hence, integrating the two machines and using a single machine for the two purposes would be technically viable and economically advantageous. This results in a more compact design solution as well. The Integrated Starter/Alternator (ISA) will be integrated directly to the crankshaft of the Internal Combustion Engine (ICE) and deliver 5 kW average and 12-15 kW peak power at 42V.