Search Results

In this study, engine-out gaseous emissions are reviewed using the Fourier Transform Infrared (FTIR) spectroscopy measurement of methanol diesel dual fuel combustion experiments performed in a heavy-duty diesel engine. Comparison to the baseline diesel-only condition shows that methanol-diesel dual fuel combustion leads to higher regulated carbon monoxide (CO) emissions and unburned hydrocarbons (UHC). However, NOX emissions were reduced effectively with increasing methanol substitution rate (MSR). Under dual-fuel operation with methanol, emissions of nitrogen oxides (NOX), including nitric oxide (NO), nitrogen dioxide (NO2), and nitrous oxide (N2O), indicate the potential to reduce the burden of NOX on diesel after-treatment devices such as selective catalytic reduction (SCR).

Soot and carbon dioxide released from internal combustion engines became the key issues when using fossil fuels. Ammonia and hydrogen having zero-carbon species can reduce carbon-related emissions and enhance the reliance on renewable fuels. A comparative study of ammonia and hydrogen impact on combustion and emission characteristics of iso-octane flame was performed under different combustion conditions. Arrhenius equation, soot surface reactions, and modified kinetic mechanism were used to study the flame growth, soot nucleation, and surface growth rates. The results show that hydrogen increased the temperature about 20.74 K and 59.30 K, whereas ammonia reduced it about 82.17 K and 66.03 K at premixed and counterflow conditions, respectively. The flame speed of iso-octane was increased 43.83 cm/s by hydrogen and decreased 34.36 cm/s by ammonia. A reduction in CH2O caused a reduction in CO and CO2 emissions.

Internal combustion engines, as the dominant power source in the transportation sector and the primary contributor to carbon emissions, face both significant challenges and opportunities in the context of achieving carbon neutral goal. Biofuels, such as biodiesel produced from biomass, and zero-carbon fuel ammonia, can serve as alternative fuels for achieving cleaner combustion in internal combustion engines. The dual-fuel combustion of ammonia-biodiesel not only effectively reduces carbon emissions but also exhibits promising combustion performance, offering a favorable avenue for future applications. However, challenges arise in the form of unburned ammonia (NH3) and N2O emissions. This study, based on a ammonia-biodiesel duel-fuel engine modified from a heavy-duty diesel engine, delves into the impact of adjustments in the two-stage injection strategy on the combustion and emission characteristics.

Net-Zero emission ambitions coupled with availability of oxygenated fuels like ethanol encouraged the Government towards commercial implementation of fuels like E20. In this background, a study was taken up to assess the impact of alcohol blended fuels on performance and emission characteristics of a BS-VI complaint motorbike. A single cylinder, 113-cc spark ignition, ECU based electronic fuel injection motorbike was used for conducting tests. Pure gasoline (E0), 10% ethanol-gasoline (E10), 20% ethanol-gasoline (E20) and 15% methanol-gasoline (M15) blends meeting respective IS standards were used as test fuels. The oxygen content of E10, E20 and M15 fuels were 3.7%, 7.4% and 8.35% by weight respectively. Experiments were conducted following worldwide motorcycle test cycle (WMTC) as per AIS 137 standard and wide-open-throttle (WOT) test cycle, using chassis dynamometer.

World is moving towards cleaner, greener and energy efficient fuels. The rapid increase in the consumption of petroleum fuel has led to twin problem of air pollution and energy security. India being a developing nation, fuel demand and consumption in various industries, especially in road transport sector has been rising continuously. Fossil fuels are the main source of energy and approximately 85% of domestic need met through import of crude oil. The increasing fuel consumption has created interest for the blending of biofuels in conventional fuel and renewable fuels also. Among biofuels ethanol is one of them and preferable choice for blending in gasoline which is a fuel for spark ignition engines and flex fuel vehicles. As such ethanol/methanol cannot be used in compression-ignition diesel engines without engine modifications due to inherent low cetane number and lubricity of alcohols.

A numerical investigation of a six-stroke direct injection compression ignition engine operation in a low temperature combustion (LTC) regime is presented. The fuel employed is a gasoline-like oxygenated fuel consisting of 90% isobutanol and 10% diethyl ether (DEE) by volume to match the reactivity of conventional gasoline with octane number 87. The computational simulations of the in-cylinder processes were performed using a high-fidelity multidimensional in-house 3D CFD code (MTU-MRNT) with improved spray-sub models and CHEMKIN library. The combustion chemistry was described using a two-component (isobutanol and DEE) fuel model whose oxidation pathways were given by a reaction mechanism with 177 species and 796 reactions.

The present study aims to determine the comparative performance evaluation in terms of fuel economy (kmpl) and wide open throttle (WOT) power derived from set of different blends of high octane gasoline fuel(s) i.e., Neat Gasoline (E0), E10 & E20 (With different dosages of additives) in high compression ratio (HCR) motorcycle on chassis dynamometer facility. With the Government of India focus on use of alcohol as co-blend of gasoline with the endeavour to save foreign exchange and also to reduce greenhouse gases (GHG) emissions. The commercially available blended fuels, E10 & E20, have high research octane number (RON, 92-100) and as per the available literature high RON fuel have the better anti-knocking tendencies thereby lead to higher fuel economy. There are various routes to formulate high octane fuel (refining technologies, additive approach & ethanol blending route) in the range of 92-100 octane number which are currently commercialized in Indian market.

The strategy for emission reduction in the P2.5 hybrid system involves the optimization of engine torque, engine speed, catalyst heat duration, and motor torque regulation in a coordinated manner. In addition to employing traditional engine control methods used in HEV models, unique approaches can be utilized to effectively manage emissions. The primary principle is to ensure that the engine operates predominantly under steady-state conditions or limits its load to regulate emissions levels. The main contributions of this paper are as follows: The first is the optimization of catalyst heating stage. During the catalyst heating stage, the system divides it into one or two stages. In the first stage, the vehicle is driven by the motor while keeping the engine idle. This approach stabilizes catalyst heating and prevents fluctuations in air-fuel ratio caused by speed and load changes that could potentially worsen emissions performance.

Recently, as part of the effort to enhance fuel efficiency and reduce costs for eco-friendly vehicles, the R-gearless system has been implemented in the TMED (P)HEV system. Due to the removal of the reverse gear, a distinct backward driving method needs to be developed, allowing the Electronic Motor (e-Motor) system to facilitate backward movement in the TMED (P)HEV system. However, the capability of backward driving with the e-Motor is limited because of partial failure in the high-voltage system of an R-gearless system. Thus, we demonstrate that it is possible to improve backward driving problems by applying a new fail-safe strategy. In the event of a high-voltage battery system failure, backward driving can be achieved using the e-Motor with constant voltage control by the Hybrid Starter Generator (HSG), as proposed in this study.

Given the growing interest in improving the efficiency of the bus fleet in public transportation systems, this paper presents an analysis of the energy consumption of a battery electric bus. During the experimental campaign, a battery electric bus was loaded using sand payloads to simulate the passenger load on board and followed another bus during regular service. Data related to the energy consumed by various bus utilities were published on the vehicle’s CAN network using the FMS standard and sampled at a frequency of 1 Hz. The collected experimental data were initially analyzed on a daily basis and then on a per-route basis. The results reveal the breakdown of energy consumption among various utilities over the course of each day of the experiment, highlighting those responsible for the highest energy consumption.

The US EPA and the California Air Resources Board (CARB) require electric vehicle range to be determined according to the Society of Automotive Engineers (SAE) surface vehicle recommended practice J1634 - Battery Electric Vehicle Energy Consumption and Range Test Procedure. In the 2021 revision of the SAE J1634, the Short Multi-Cycle Test (SMCT) was introduced. The proposed testing protocol eases the chassis dynamometer test burden by performing a 2.1-hour drive cycle on the dynamometer, followed by discharging the remaining battery energy into a battery cycler to determine the Useable Battery Energy (UBE). Opting for a cycler-based discharge is financially advantageous due to the extended operating time required to fully deplete a 70-100kWh battery commonly found in Battery Electric Vehicles (BEVs).

Plug-in hybrid electric vehicles have the potential of combining the benefits of electric vehicle in terms of low emissions and internal combustion engine vehicles in terms of vehicle range. With the addition of a renewable fuel, the CO2 potential reduction increase even more. The last trends for PHEV are small combustion engine known as range extender, with battery package between full hybrid and electric powertrains. Thus, allowing an improvement in vehicle’s range, reducing battery materials while converting fuel energy through a highly efficient path. Although these vehicles have been proved to be a convenient strategy for decarbonizing the light vehicles, the use of alternative fuels is poorly studied. In this work, hydrous ethanol is chosen because is already available in some countries, such as USA and Brazil, and have an ultra-low well-to-tank CO2 emission.

The powertrain electrification is currently not only taking place in public road mobility vehicles, but is also making its way to the racetrack, where it’s driving innovation for developments that will later be used in series production vehicles. The current development focus for electric vehicles is the balance between driving power, range and weight, which is given even greater weighting in racing. To redefine the current limits, IAV developed a complete e-powertrain for a racing MX motorcycle and integrated it into a real drivable demonstrator bike. The unique selling point is the innovative direct phase-change cooling (PCC) of the three-phase e-motor and its power electronics, which enables significantly increased continuous power (Pe = 40 kW from 7,000 rpm to 9,000 rpm) without thermal power reduction. The drive unit is powered by a replaceable Lithium-Ion round cell battery (Ubat,max = 370V) with an energy storage capacity of Ebat = 5 kWh.

Owing to its remarkable simplicity, high torque density, and expansive speed range, the switched reluctance motor (SRM) garners significant attention in the automotive industry, particularly in propelling electric vehicles. Nevertheless, the most prominent challenge faced by SRMs in their role as hub motors for electric vehicles is the unbalanced radial electromagnetic forces resulting from air gap eccentricity, which will induce motor vibration and noise, even seriously jeopardizing the driving safety of electric vehicles. Building upon the foundation of a nonlinear model for the SRM, this paper presents an analytical approach to assess the unbalanced radial forces arising from both radial and tilt air gap eccentricities. Furthermore, a test platform is constructed to validate the effectiveness of the proposed method, and comparative analyses of experiments, finite element simulations, and numerical analytical results are provided.

Focused on the permanent magnet synchronous motor (PMSM) used in electric, this paper proposes an online insulation testing method based on voltage injection under high-temperature and high-humidity conditions. The effect of constant humidity and temperature on the insulation performance has been also studied. Firstly, the high-voltage insulation structure and principle of PMSM are analyzed, while an electrical insulation testing method considered constant humidity and temperature is proposed. Finally, a temperature and humidity experimental cycling test is carried out on a certain prototype PMSM, taking heat conduction and radiation models, water vapor, and partial discharge into account. The results show that the electrical insulation performance of the motor under constant humidity and temperature operation environment exhibits a decreasing trend. This study can provide theoretical and practical references for the reliable durability design of PMSM.

The paper solves the problem of increasing the accuracy of measuring torque and use of an electronic torque meter as a feedback sensor of synchronous and induction machines of an electric traction drive. Relevance of the problem and methods for its solving by indirect means using simulation models of electric machines are considered. The theoretical development of the meter is based on the energy model of electric machines in the form of differential equations for active and reactive power balance. This eliminates the direct influence of instability and nonlinearity of inductive elements and takes into account electrical, magnetic, mechanical, and harmonic losses using the simplest algorithms. Key variables of the model in the form of total active power and angular velocity are measured directly, and the high nominal efficiency of traction machines (95%) provides a wide tolerance range for calculating total losses.

A 300 mile-range automotive battery pack is comprised of many individual cells connected in series/parallel to make up the required voltage, energy, and power. The cell groupings can take the form of parallel strings of series cell groups (S-P), series string of parallel cell groups (P-S), or a hybrid of the two. Though the different battery configurations deliver identical output voltage and energy, they exhibit varying cell level behaviors due to differing electrical structure, particularly when cell imbalance occurs. In this work, we explore the relative merits of various cell grouping configurations using a model-based approach. The emphasis of the study is to evaluate the impact of electrical variation between cell-to-cell, originating from cell manufacturing process variation, battery assembly (laser tab bonding) process variation or from normal operation, on the performance of the battery pack. A first-order equivalent circuit model is used to represent a lithium-ion cell.

Pouch cells are increasingly popular form factors for the construction of energy storage systems in electric vehicles of all classes. Knowledge of the stress generated by these higher capacity pouch cells is critical to properly design battery modules and packs for both normal and abnormal operation. Existing literature predominantly offers data on smaller pouch cells with capacities of less than 10 Ah, leaving a gap in our understanding of the behavior of these larger cells. This experimental study aimed to bridge this knowledge gap by measuring loads and stresses in constrained 65 Ah pouch cells under both cycling and abuse conditions. To capture the desired responses, a load cell was located within a robust fixture to measure cell stress in real time after the application of a preload of approximately 30 kilograms or 294 N, equivalent to a pressure of 0.063 bar, with a fixed displacement.

Electrification is the future of the automotive industry and with the rapid growth of Battery Electric Vehicle (BEV) market, battery protection becomes more and more crucial. Side pole impact is one of the most challenging safety load cases. Rocker assembly, as the first line of defense, plays a significant role during the event. This paper proposes Cleveland-Cliffs Steel Tube as Reinforcement (C-STARTM) protection as an application for rocker reinforcement. For a component level assessment, three-point bending is used as a testing method to replicate pole impact. The performance is compared with aluminum baseline with respect to peak force and energy absorption. Test and CAE simulations have been performed and a well calibrated CAE model is utilized to predict the robustness of various steel designs using different grades, gauges and geometries.

Lithium-ion cells operate under a narrow range of voltage, current, and temperature limits, which requires a battery management system (BMS) to sense, control, and balance the battery pack. The state of power (SOP) estimation is a fundamental algorithm of the BMS. It operates as a dynamic safety limit, preventing rapid ageing and optimizing power delivery. SOP estimation relies on predictive algorithms to determine charge and discharge power limits sustainable within a specified time frame, ensuring the cell design constraints are not violated. This paper explores various approaches for real-time deployment of SOP estimation algorithms for a high-power lithium-ion battery (LIB) with a low-cost microcontroller. The algorithms are based on a root-finding approach and a first-order equivalent circuit model (ECM) of the battery.