Search Results

The transition towards battery electric vehicles (BEVs) has increased the focus of vehicle manufacturers on energy efficiency. Ensuring adequate airflow through the heat exchanger is necessary to climatize the vehicle, at the cost of an increase in the aerodynamic drag. With lower cooling airflow requirements in BEVs during driving, the front air intakes could be made smaller and thus be placed with greater freedom. This paper explores the effects on exterior aerodynamics caused by securing a constant cooling airflow through intakes at various positions across the front of the vehicle. High-fidelity simulations were performed on a variation of the open-source AeroSUV model that is more representative of a BEV configuration. To focus on the exterior aerodynamic changes, and under the assumption that the cooling requirements would remain the same for a given driving condition, a constant mass flow boundary condition was defined at the cooling airflow inlets and outlets.

A 2-D computational model was developed to describe the flow and filtration processes, in a honeycomb structured ceramic diesel particulate trap. This model describes the steady state trap loading, as well as the transient behavior of the flow and filtration processes. The theoretical model includes the effect of a copper fuel additive on trap loading and transient operation. The convective terms were based on a 2-D analytical flow field solution derived from the conservation of mass and momentum equations. The filtration theory incorporated in the time dependent numerical code included the diffusion, inertia, and direct interception mechanisms. Based on a measured upstream particle size distribution, using the filtration theory, the downstream particle size distribution was calculated. The theoretical filtration efficiency, based on particle size distribution, agreed very well (within 1%) with experimental data for a number of different cases.

Automotive cylinder head gaskets today must not only ensure a dry joint, they must also assist in minimizing cylinder bore and cam journal distortion, decrease crevice volume to help meet stringent emissions requirements, and have the durability to perform well over extended warranty periods. In order to accomplish these varied goals, Multi-Layer Steel gaskets are proving to be the design of choice in an increasing number of automotive cylinder head gasket applications. This paper will discuss how and why a specific design methodology for multi-layer steel cylinder head gaskets successfully addresses today's engine manufacturers' requirements and shows additional promise for the future.

Tire marks left by the vehicle prior to impact, rollover, or other event, are important forensic evidence reconstruction of motor vehicle accidents. Often these tire marks have some curvature that is measured and used to calculate the speed of vehicles prior to the event. This calculation is based on the coefficient of friction of the tire/road interface and the radius of curvature of the vehicle center of gravity (c.g.) path. There is controversy about the validity of this approach. To explore this theory, a test vehicle was driven through a series of maneuvers that produced yaw marks for direct comparison of actual vehicle velocity to the velocity calculated by the critical speed formula. Test results show the critical speed formula is inaccurate for most circumstances and does not correctly describe vehicle limit performance behavior.

The human body is most sensitive to low frequency whole body vibrations. Ride vibrations of off-road vehicles, caused primarily by irregular terrains, predominate in the 0.5 - 5 Hz frequency range. A suspension seat offers the simplest means to improve vehicle ride by reducing ride vibrations transmitted to the driver. A computer model of an off-road vehicle suspension seat was developed which can aid the designer in the selection of optimal suspension parameters. A parametric study was performed to determine the frequency response characteristics of the validated suspension model via computer simulation to investigate the influence of suspension parameters on the vibration transmission performance of suspension seats.

In this study, henequen fibers that had been treated with NaOH were used as reinforcements in phenolic-based materials. The hot-pressing method was used to create composites, which were then tested for tensile, flexural, fundamental, and thermogravimetric characteristics. When compared with samples that were untreated, the total attributes of fiber interface modification and treatment improved. The treated varieties of 50% henequen materials had the best tensile qualities of all composites, although their flexural values fell somewhat in comparison to the unprocessed materials. Fiber processing reduced the three-point bending characteristics of henequen composites. SEM was used to investigate the behavior of matrix and fiber bonding prior to and following pretreatment. Processed with 50% henequen resulted in improved fiber dispersion, 60% henequen resulted in void content, whereas 40% henequen resulted in inadequate fiber/matrix interface bonding.

Aluminum and its alloys entered a main role in the engineering sectors because of their applicable characteristics for indispensable applications. To enhance requisite belongings for the components, the composition of variant metal/nonmetal with light metal alloys is essential in the manufacturing industries. To enhance the wear resistance with significant strength property of the aluminum alloy 2024, the reinforcement SiC and fly ash (FA) were added with the designation Al2024 + 10% SiC; Al2024 + 5% SiC + 5% FA; and Al2024 + 10% FA via stir-casting technique. The wear resistance property of the composites was tested in pin-on-disc with a dry-sliding wear test procedure. The experiment trials were designed in Box–Behnken design (BBD) by differing the wear test parameters like % of reinforcement, sliding distance (m), and load (N).

Let’s start with the uncomfortable truth, climate change is happening, and the automotive industrial network is one of the main industries contributing to greenhouse gas emissions. SKF is an energy intensive business – directly using energy, mainly in the form of electricity and gas, in its operations around the world. In addition, SKF utilizes materials, predominantly steel, and services which can be energy and carbon intensive – such as transports and raw material in production and processing. The combined impact of these direct and indirect energy uses (scope 1, 2 and 3 upstream) generates an excess of over two million metric tons of CO2e per year. This figure would however be significantly higher were it not for the actions SKF has taken to reduce both energy and carbon intensity. In 2000, we were one of the first companies to actually start to report and set climate targets.

A ban on Per- and Polyfluorinated Substances (PFAS) has enforced automobile companies to find alternatives to current R1234yf refrigerant. One such natural substitute, R290 (propane), is becoming popular with automotive manufacturers and suppliers due to its high performance and efficiency. However, due to its high flammability, R290 is not allowed in the cabin evaporator/condenser in order to ensure the safety of the driver and passenger. This requires the design of a novel indirect Heat Flux Management System (HFMS) with coolant as a working fluid to transfer heating to cabin and powertrain cooling components. The design of the heat pump system confines flammable R290 refrigerant to a hermitic compact box to avoid leakages. This paper aims to investigate the performance and efficiency of a new R290 refrigerant-based indirect heat pump system. The system is tested on a test bench, and the results are compared to an indirect heat pump system with R1234yf refrigerant.

Per - and polyfluoroalkyl substances – known as PFAS are man-made chemicals that do not occur naturally. PFAS are widely used, long lasting chemicals, components of which break down very slowly over time. Scientific studies have shown that exposure to some PFAS in the environment may be linked to harmful health effects in humans and animals. Because of their widespread use and their persistence in the environment, many PFAS are found in human and animals’ blood all over the world and are present at low levels in a variety of food products and in the environment. PFAS are found in water, air, fish, and soil at locations across the nation and the globe. Both refrigerants (HFC-134a & HFO-1234yf) that are currently used in mobile air conditioning systems (MACS) create PFAS. Hence, various countries are looking into banning chemicals that create PFAS. Natural refrigerants are being proposed as alternative refrigerants as they do not create PFAS.

In the present investigation a tractor wheel runover accident was simulated to obtain biomechanical information relating to mechanism of injury. Twelve cadaver porcine specimens were runover with the right front wheel of a tractor. Specimens were placed on a six-axis force plate and thorax contours were recorded temporally. Results indicated up to 68% compression of the chest occurred during the runover event. The shear force in the direction of travel was a significant factor in the type of fractures that occurred to the rib cage. Pathology determined from x-ray revealed multiple fractures per rib in the area directly below the path of the tire. Autopsy evaluation revealed soft tissue contusion on the left side in the area of wheel path. There was often extra blood in the pericardial space and examination of the brain showed petechial hemorrhaging subdurally.

A new hybrid transmission has been developed for all-wheel-drive (AWD) cars, and is used in the new Lexus LS600h and LS600hL for its first application. It has a compact layout consisting of a power-split device, generator, high-output electric motor, and a two-stage speed reduction device. Combined with a 5-liter V-8 engine, it achieves power performance rivaling 6-liter engine vehicles, the fuel efficiency of a medium-class vehicle, and outstanding quietness. This paper describes the structure, performance, and shift control technology of this hybrid transmission.

When vehicle-specific stiffness coefficients cannot be acquired, stiffness coefficient values that are representative of the desired vehicle type, class, wheelbase or weight are routinely used for accident reconstructions. Since the original compilation of representative vehicle stiffness data almost 20 years ago, changes in crash testing standards and other safety and technological improvements in vehicular design have affected vehicle stiffness. While generic frontal stiffness data have been recently updated to reflect these vehicular changes, rear and side stiffness data have not. Structural, geometric and inertial data for over 300 passenger cars and light trucks were collected. Among the vehicles targeted were the top-selling cars, SUVs, vans and pickups for model years 1990 to 2012. Results indicated that all vehicle types demonstrated increases in mean stiffness over the time period considered. SUVs were, on average, the stiffest vehicle type in the front, rear and side.

In recent years, the push for reduced product development timelines has been more than ever with significant changes in the automotive market. High electrification, intelligent vehicle systems and increased number for car manufacturers are a few key drivers to the same. The front loading of development activities is now a key focus area for achieving faster product development. From vehicle dynamics point of view availability of subjective evaluation feedback plays a key role in optimization various system specifications. This paper discusses an approach for front loading through parallel development of the tire and vehicle chassis system, using advanced simulation and driving simulator technology. The proposed methodology uses virtual tire models which in combination with real-time vehicle model enables subjective evaluation of vehicle performance in driver-in-loop simulators.

The environmental and sustainable energy concerns in transport are being addressed through the decarbonisation path and the potential of hydrogen as a zero-carbon alternative fuel. Using hydrogen to replace fossil fuels in various internal combustion engines shows promise in enhancing efficiency and achieving carbon-neutral outcomes. This study presents an experimental investigation of hydrogen (H2) combustion and engine performance in a boosted spark ignition (SI) engine. The H2 engine incorporates both port fuel injection (PFI) and direct injection (DI) hydrogen fuel systems, capable of injecting hydrogen at pressures of up to 4000 kPa in the DI system and 1000 kPa in the PFI operations. This setup enables a direct comparison of the performance and emissions of the PFI and DI operations. The study involves varying the relative air-to-hydrogen ratio (λ) at different speeds to explore combustion and engine limits for categorising and optimising operational regions.

The European Union aims to be climate neutral by 2050 and requires the transport sector to reduce their emissions by 90%. The deployment of H2ICE to power vehicles is one of the solutions proposed. Indeed, H2ICEs in vehicles can reduce local pollution, reduce global emissions of CO2 and increase efficiency. Although H2ICEs could be rapidly introduced, investigations on hydrogen combustion in ICEs are still required. This paper aims to experimentally compare a flat piston and a bowl piston in terms of performances, emissions and abnormal combustions. Tests were performed with the help of a single cylinder Diesel engine which has been modified. In particular, a center direct injector dedicated to H2 injection and a side-mounted spark plug were installed, and the compression ratio was reduced to 12.7:1. Several exhaust gas measurement systems complete the testbed to monitor exhaust NOx and H2.

In electric-powertrains, noise and vibration can be generated by components such as gears and motors. Often a noise phenomenon known as rumble or droning noise can occur due to low shaft order excitation at the spline. In this study, we identified the excitation source for spline induced rumble noise and developed a novel analysis method. First, a detailed spline model, believed to be the key factor for rumble noise, has been developed and verified by comparison with Finite Element Method(FEM) analysis. In order to identify an excitation source, a typical electric-powertrain assembly model including the developed spline model was constructed and simulated. Results according to changes of key factors including spline pitch errors and shaft alignment errors were analyzed. Spline radial force has been identified as an excitation source of spline induced rumble noise. This was verified through comparison with the forced vibration analysis result and time domain analysis result.