Search Results

A single cylinder carburetor SI engine with a modified L type cylinder head and equipped with a fuel injector was used to inject methanol into the combustion chamber. Four series of runs at an engine speed of 2500 rpm were made. One series with different values of λ* was performed with gasoline, and the other three series methanol was injected into the gasoline-air mixture. Each series of methanol injected run was supplied with the same energy input per cycle to correspond to that of the gasoline. The results of the experiments indicated that the performance (BHP) of the engine was proportional to the energy input of the mixture up to about 50% methanol injected. With the equivalence air-fuel ratio above λ = 1.15 (lean mixture), it was found the NOx concentration decreased more than 30% while the BSFC remained constant.

This experimental study was conducted in a motored research engine to investigate the effect of blending methanol and ethanol on hydrocarbon oxidation and autoignition. An 87 octane mixture of primary reference fuels, 87 PRF, was blended with small percentages of the alcohols to yield a constant gravimetric oxygen percentage in the fuel. The stoichiometric fuel mixtures and neat methanol and ethanol were tested in a modified single-cylinder engine at a compression ratio of 8.2. Supercharging and heating of the intake charge were used to control reactivity. The inlet gas temperature was increased from 325 K to the point of autoignition or the maximum achievable temperature of 500 K. Exhaust carbon monoxide levels and in-cylinder pressure histories were monitored in order to determine and quantify reactivity.

This report presents the Auto/Oil AQIRP results of a methanol fueled vehicle emission study. Nineteen early prototype flexible/variable fueled vehicles (FFV/VFV) were emission tested with industry average gasoline (M0), an 85% methanol-gasoline blend (M85), and a splash-blend of M85 with M0 (gasoline) giving 10% methanol (M10). Vehicle emissions were analyzed for the FTP exhaust emissions, SHED diurnal and hot soak evaporative emissions, and running loss evaporative emissions. Measurements were made for HC, CO and NOx emissions and up to 151 organic emission species, including air toxic components. M0 and M10 emissions were very similar except for elevated M10 evaporative emissions resulting from the high M10 fuel vapor pressure. M85 showed lower exhaust emissions than M0 for NMHC (non-methane hydrocarbon), OMHCE (organic material hydrocarbon equivalent), CO and most species. M85 had higher exhaust emissions for NMOG (non-methane organic gases), NOx, methanol and formaldehyde.

It has been observed that a certain percentage of diesel particulate filters (DPFs) from the field form mid-channel ash plugs both in light duty and heavy duty applications. As revealed in a post mortem study, some field samples have ash plugs of 3-10 cm length in the middle of DPF inlet channels, which can potentially reduce the inlet channel volume by more than 50%. As a result, the mid-channel ash plug reduces the effective filtration area and decreases the effective channel open width in the middle of the channel. This explains why these filters are reported as having large increases in pressure drop. Moreover, the mid-channel ash deposits reduce the DPF service life and render the filter cleaning process ineffective. In the present study, an open source CFD tool is applied to study the 3D flow crossing two representative inlet and outlet DPF channels where the inlet channels have mid-channel ash plugs.

Vehicle suspension systems that adopt Hotchkiss layout are commonly based on leaf springs. For better comfort for passengers, some features such as rubber pads are used on the springs to reduce noise from metallic contact between leaves, but those pads can compromise the durability of the spring if not well designed or located in the spring assembly, as we will demonstrate on this paper. To do so, it will be presented comparisons using CAE methodology and physical parts test results from vehicle and bench testing which were loaded in different conditions to demonstrate how the rubber pad position can influence the durability of the spring, especially near the eyelet region for some specific load conditions. The case studies presented here are focused on the impact of the rubber pads on durability life of springs, but not defined as root cause of failures.

Previous research in our laboratory has shown that NOx emissions can be sharply reduced by PREDIC (PRE-mixed lean DIesel Combustion), in which fuel is injected very early in the compression process. However some problems still remain, such as higher fuel consumption, a lack of ignition timing control, and a large increase in THC and CO, compared to conventional diesel combustion. Appropriate mixture formation is necessary to solve these problems. In this paper, the influence of mixture formation on PREDIC was investigated. It was found that the pintle type injection nozzle was shown to be suitable for PREDIC, because it produced a comparatively uniform mixture in the combustion chamber and avoided collision of the fuel spray with the cylinder liner. Modeling by the KIVA-II software package was carried out to improve our understanding of the mixture formation process.

The object of this research was to learn more about the effects of mixture motion upon ignition in spark ignited piston engines, and to determine how variations in mixture velocity alter the combustion process. To provide effective means for producing and measuring the mixture velocity, all tests were made in a constant volume bomb, using mixtures of propane and air. The effects of mixture motion on the lean spark ignition limit, rate of pressure rise, and burning time were determined for mixture ratios ranging from stoichiometric to the lean limit. The mixture pressures corresponded to those in Otto cycle engines at the time of spark occurrence. The results reveal that a mixture velocity of 50 fps, relative to the spark plug, requires an enrichment of 17% with respect to the stagnant lean limit. Increases in mixture velocity were found to greatly increase the rate of pressure rise during combustion. This effect was more pronounced for lean mixtures than for stoichiometric mixtures.

The role of mixture stratification on combustion rate has been investigated in a constant volume combustion vessel in which mixtures of different equivalence ratios can be added in a spatially and temporally controlled fashion. The experiments were performed in a regime of low fluid motion to avoid the complicating effects of turbulence generated by the injection of different masses of fluid. Different mixture combinations were investigated while maintaining a constant overall equivalence ratio and initial pressure. The results indicate that the highest combustion rate for an overall lean mixture is obtained when all of the fuel is contained in a stoichiometric mixture in the vicinity of the ignition source. This is the result of the high burning velocity of these mixtures, and the complete oxidation which releases the full chemical energy.

Influence coefficient balancing of an advanced gas turbine rotor in fluid-film bearings with nonsymmetrical properties has been examined. The effect of the number of balancing planes in use of the quality of balance has been studied with particular attention being paid to the reasons why an increase from three planes to four planes gives no apparent improvement. Effects examined include the influence of nonsymmetrical bearing properties, the effect of having a bending critical speed close to either side of the intended operating speed, and the effect of correction weight errors on balance quality. Reasons why the addition of a fifth balancing plane resulted in a significant improvement in balance quality are given.

In a diesel engine, the combustion and emissions formation are governed by the spray formation and mixing processes. To meet the stringent emission legislations of the future, which will demand substantial reductions of NOX and particulate emissions from diesel engines, the spray and mixing processes play a major roll. Different fuel injection systems and injection strategies have been developed to achieve better performance and lower emissions from the diesel engine almost without investigating the influence of the injector nozzle orifices. A reduction in the nozzle orifice diameter is important for an increased mixing rate and formation of smaller droplets which is beneficial from emissions and fuel consumption point of view, as long as the local air-to-fuel ratio (AFR) is kept at a sufficiently lean level.

The purpose of this study was to provide biomechanical data for the improvement and validation of active human models. A drop test setup was developed for the measurement of dynamic soft tissue characteristics in dependence of the muscle activation state. The tests revealed different energy dissipation properties for relaxed and activated muscle tissue. For the investigation of the influence of muscle activity on human kinematics a low-impact volunteer pendulum test was designed. The posture maintenance of seated subjects was tested by frontal, lateral and rearward pendulum impacts to the upper torso. The kinematics was recorded with an optical movement analysis system and muscle responses were detected via EMG. Smaller displacements of the head and upper torso were observed in tests with pre-activated muscles. The obtained data were used in the validation of a finite element human body model (HUMOS).

Controlling start of ignition in Homogenous Charge Compression Ignition (HCCI) engines remains a major challenge. Here we have investigated changes in intake charge composition and its effects on ignition delay for natural gas based HCCI engine operation. In particular, we have investigated the effects of small amounts of nitrogen dioxide (NO2) on operating characteristics. Previous research had shown that NOx presence might attenuate natural gas ignition. The hypothesized catalytic effect of NOx on methane ignition at HCCI conditions was experimentally confirmed in a custom built engine. The problem was further studied in both zero and multidimensional numerical engine simulations with detailed chemistry. The simulations were used to complete a reaction rate sensitivity analysis to elucidate the controlling chemistry, and further confirm that a significant shift in ignition phasing is produced with the addition of just several ppm by volume of NO2 or NOx (NO + NO2).

This paper demonstrates the effects of nano-clay on the microcellular foam processing of nylon. First, Nylon 6 nanocomposites with 1 wt% clay were prepared by a twin screw extruder. The nanocomposite structures were characterized by XRD and TEM. Nylon and its nanocomposites were foamed in extrusion using CO2. The cell morphologies of nylon and its nanocomposite foams were investigated. It appeared that the nano-clay not only enhanced cell nucleation, but also suppressed cell deterioration in the microcellular foaming of nylon.

Elastomers are traditionally designed for use in applications that require specific mechanical properties. Unfortunately, these properties change with respect to many different variables including heat, light, fatigue, oxygen, ozone, and the catalytic effects of trace elements. When elastomeric mounts are designed for NVH use in vehicles, they are designed to isolate specific unwanted frequencies. As the elastomers age however, the desired elastomeric properties may have changed with time. This study looks at the variability seen in new vehicle engine mounts and how the dynamic properties change with respect to miles accumulated on fleet and durability test vehicles.

The effects of using neat FAME (Fatty Acid Methyl Ester) in a modern small displacement passenger car diesel engine have been evaluated in this paper. In particular the effects on engine performance at full load with standard (i.e., without any special tuning) ECU calibration were analyzed, highlighting some issues in the low end torque due to the lower exhaust gas temperatures at the turbine inlet, which caused a remarkable decrease of the available boost, with a substantial decrease of the engine torque output, far beyond the expected engine derating due to the lower LHV of the fuel. However, further tests carried out after ECU recalibration, showed that the same torque levels measured under diesel operation can be obtained with neat biodiesel too, thus highlighting the potential for maintaining the same level of performance.

The scope of this paper is to determine the affects that non-petroleum based fuels such as: rapeseed methyl ester (RME) and soy methyl ester (SME) have on thermoset elastomers. The thermoset elastomers that have been evaluated are NBR (Nitrile Butadiene Rubber), NBR/PVC (Nitrile Butadiene Rubber & Polyvinyl Chloride), Epichlorohydrin homo- (Homopolymer of Epichlorohydrin), co- (Copolymer of Epichlorohydrin), ter- (Terpolymer of Ecpichlorohydrin), and Di-, and ter FKM (Fluorinated Rubber). The different elastomers have been subjected to aging in neat fatty acid methyl esters, RME and SME, at a variety of durations and temperatures. The effects of this exposure on the properties of thermoset elastomers are described in this paper.

A rotor-shaft system supported at one end by a spline coupling, and at the other end by a flexible bearing support having asymmetric and nonlinear characteristics is analyzed. The effects of nonlinearity and asymmetry in the flexible support, on the response to excitation from sliding friction in the spline coupling and rotor unbalance are investigated. The spline friction is represented as coulomb friction. As a result of the sliding friction excitation, a bounded nonsynchronous whirl is shown to occur at rotational speeds above the undamped natural frequency of the system.

The injuries sustained by elderly car occupants in traffic accidents are usually more severe than those of younger occupants. Accident statistics data show that injuries to elderly occupants frequently occur in the chest. Belted drivers and front seat passengers in cars involved in frontal collisions were investigated using detailed data on traffic accidents in Japan. From a total of 246 vehicle occupants, the total number of injuries among the 167 occupants listed as injured was 462. Most of the injuries to the chest were minor ones such as skin abrasions or contusions. However, 21 occupants sustained rib fractures and 7 persons even sustained internal organ injuries. Younger occupants appeared not to sustain rib fractures even in higher impact collisions. Conversely, elderly occupants frequently experienced rib fractures near the seat belt line even under lower impact severity.

The effects of Whiplash Associated Disorder (WAD) from low speed rear-end collisions (REC) have been reported in the medical, scientific and engineering literature for several decades. Given the method of analysis, results have varied regarding the nature, onset and severity of spinal injury. While previously conducted laboratory crash tests have advanced the understanding of occupant dynamics from RECs, concern over investigative methodology and experimental artificiality remains. The purpose of this study is to determine if any relationship existed between specific occupant characteristics, vehicular acceleration and the onset and severity of WAD. Ninety-five subjects involved in real world RECs are selected from an active database. Data is collected over an 18-month period. Fifty-nine subjects are females and 70% of the subjects are drivers.

This paper presents results of studies investigating the effect of octane enhancing ethers on the reactivity of an 87 octane mixture of primary reference fuels, 87 PRF, in a motored engine. 87 PRF was blended with small percentages of MTBE, ETBE, TAME and DIPE based on a constant gravimetric oxygen percentage in the fuel. The experiments were conducted in a modified single-cylinder Wisconsin AENL engine at compression ratios of 5.2 and 8.2. Supercharging and heating of the intake charge were used to control reactivity. The inlet gas temperature was increased from 320 K, where no reactivity occurred, until either autoignition occurred or the maximum temperature of the facility was reached. Exhaust carbon monoxide levels and in-cylinder pressure histories were monitored in order to determine and quantify reactivity.