Search Results

The accuracy of the Powertrain Control Module (PCM) Event Data Recorder (EDR) was tested on a 2009 Ford Crown Victoria Police Interceptor during both straight line steady state conditions and maximum ABS braking, at the Michigan State Police training facility in Lansing, MI. Six runs were made starting from 64 km/h (40 mph) and six runs starting from 96km/h (60 mph). Data was collected from the PCM EDR and the primary speed reference instrumentation was a Racelogic VBOX III (with IMU) 100 Hz differential GPS speed data acquisition system. On selected runs Radar was used as additional steady state speed verification and for the braking portion a Vericom 3000 was used to verify speed loss and calculated stop distance. Visible ABS tire marks were documented following each test, and the length of marks was compared to the calculated braking distance from each measurement device. Graphs of PCM speed/brake/accel pedal data versus VBOX speed over time are presented.

This paper describes the design concept and characteristics created to develop a new 200 hp class crawler tractor and the subsequent test to assume the achievement of objectives. The new tractor provides a stable platform for good control of the dozer blade and ripper, a main frame for independent mounting of the hydraulically controlled power train and superstructure components, easy servicing of power train components, integration of the ROPS with the chassis, and a 210 hp engine at 2100 rpm.

This paper describes a series of 200–300 hp gas turbine engines being developed by the AiResearch-Phoenix Division of the Garrett Corp. for the U.S. Army Engineer Research and Development Laboratories. These engines, which include both simple cycle and regenerative types, are intended for ground power applications, primarily for direct driving high speed equipment such as high frequency alternators. Descriptions are given of the basic approach taken to meet the Army’s requirements, the resulting engine configurations, the development progress to date, and future program plans and timing.

This paper examines the powertrain and braking efficiency of a wide spectrum of light duty vehicles to illustrate the range of efficiencies that exist and to isolate the contribution of hybrid and non-hybrid powertrains in reducing fuel consumption. The paper also examines the change in vehicle energy demands, e.g. aerodynamics and rolling resistance from 2005 models to 2010 models to highlight the role that vehicle energy consumption reduction plays in determining total fuel consumption. EPA fuel economy certification data is analyzed using the metrics of vehicle limited fuel consumption and powertrain and braking efficiency. From the data, conclusions are drawn to create a list of the ten most efficient powertrains, based on the powertrain and braking efficiency metric, and the ten vehicles with the lowest vehicle limited fuel consumption. These metrics provide an informative basis for current and future technology evaluations.

The 2013 SRT Viper Carbon Fiber X-Brace, styled by Chrysler's Product Design Office (PDO), is as much of a work of art as it is an engineered structural component. Presented in this paper is the design evolution, development and performance refinement of the composite X-Brace (shown in Figure 1). The single-piece, all Carbon Fiber Reinforced Plastic (CFRP) X-Brace, an important structural component of the body system, was developed from lightweight carbon fiber material to maximize weight reduction and meet performance targets. The development process was driven extensively by virtual engineering, which applied CAE analysis and results to drive the design and improve the design efficiency. Topology optimization and section optimization were used to generate the initial design's shape, form and profile, while respecting the package requirements of the engine compartment.

Various techniques are constantly being devised to accelerate model generation leading to shorter product development cycle. This work proposes and implements a reduced synthetic gas bench (SGB) test protocol for a commercial Pt-Pd diesel oxidation catalyst (DOC) that can be used to develop global reaction kinetics. The kinetics thus developed were implemented in a 1D model to predict DOC emissions accurately over a wide operating window. Hydrocarbons (HCs) in the exhaust were categorized as Propylene (C3H6) representing partially oxidized hydrocarbons and n-Decane (C10H22) representing unburnt fuel. Test protocols were defined using the order of inhibition of the various species present in the exhaust, namely, CO, NOx (NO+NO2) and HC for the specific reaction under consideration. The oxidation reactions for CO and HCs were found to be inhibited competitively by CO and HCs; both the NOx species inhibited these reactions to the same extent.

To effectively utilize larger trucks (85 ton and up), open-pit mines and quarries need a larger front-end loader with high reliability and performance. This paper describes the design approach and tests carried out to design 21 cubic yard 580 PAY® loader to meet these requirements. Long fatigue life of structures was obtained by use of full penetration welds. New concept for power control was designed to effectively distribute power between hydraulics and drive train. Spring applied - pressure released brakes were designed into the axle. Tests were carried out in our laboratory and proving grounds to determine performance and reliability.

We have developed a small-displacement gasoline direct-injection engine (1.3L). Gasoline direct-injection engines rely on ultra-lean stratified combustion to deliver significantly better fuel economy, and are already used in many practical applications. When gasoline direct-injection is applied to a small-displacement engine, however, the amount of wall wetting of fuel on the piston surface will increase because the traveled length of the fuel spray is short. This may result in problems such as smoke production, high emissions of unburned HC, and poor combustion efficiency.

The U. S. Coast Guard has recently put into service new 210 ft cutters designed for search and rescue work, law enforcement, oceanographic work, and possible future ASW. This paper outlines the structure and capabilities of the vessel. An important feature of the cutter is its helicopter handling facilities, which have greatly increased the cutter's search and rescue capability by extending the area it can cover. The cutter is the first in Coast Guard service to be powered by a combination diesel engine and gas turbine installation. The combination gives a top speed of 18 knots and a cruising range of 5000 miles.

Current developments in automotive industry such as hybrid powertrains and the continuously increasing demands on emission control systems, are pushing complexity still further. Validation of such systems lead to a huge amount of test cases and hence extreme testing efforts on the road. At the same time the pressure to reduce costs and minimize development time is creating challenging boundaries on development teams. Therefore, it is of utmost importance to utilize testing and validation prototypes in the most efficient way. It is necessary to apply high levels of instrumentation and collect as much data as possible. And a streamlined data pipeline allows the fleet managers to get new insights from the raw data and control the validation vehicles as well as the development team in the most efficient way. In this paper we will demonstrate a data-driven approach for validation testing.

Aircraft potable (drinking) water systems haven’t changed significantly in the last half-century. These systems consist of cylindrical water tanks pressurized by bleed air from the jet engines, with insulated stainless steel distribution lines. What has changed recently is the increase in the possibility of aircraft picking up contaminated drinking water at foreign and domestic stops. Customer awareness of these problems has also changed - to the point where having reliable drinking water is now a competitive issue among airlines. Old style potable water systems that are used on modern aircraft are high maintenance and exacerbate the growth of microbes because the water is static much of the time. The integrity of some pressurized water tanks are also a concern after years of use. Cost-effective mechanical and biological solutions exist that can significantly reduce the amount of chemicals added and provide good potable water.

On January 14, 2004 President George W Bush outlined a new vision for NASA that has humans venturing back to the moon by 2020. With this ambitious goal, new tools and models have been developed to help define and predict the amount of space radiation astronauts will be exposed to during transit and habitation on the moon. A representative scenario is used that includes a trajectory from LEO to a Lunar Base, and simplified CAD models for the transit and habitat structures. For this study galactic cosmic rays, solar proton events, and trapped electron and proton environments are simulated using new dynamic environment models to generate energetic electron, and light and heavy ion fluences. Detailed calculations are presented to assess the human exposure for transit segments and surface stays.

This paper describes how the 21st Century Truck Initiative supports the U.S. Army's transformation to a lighter, more mobile force to meet future National Security needs while helping commercial users develop economically viable technologies to lower costs and reduce demands for foreign fuel. The paper will also show how the National Automotive Center's systems engineering approach supports the selection of emerging technologies to support the transformation process.