Search Results

Today, some vehicles include a regenerative-braking system such as the electrical motor-generator that converts the vehicle's kinetic energy into electrical energy to recharge one or more vehicle batteries. The idea is to use air flow to produce additional electrical energy in response to deceleration of the vehicle. With the Wind Power Generator System (WPGS) as a green system, a vehicle can produce extra energy, reduce gasoline usage, and reduce air pollution.

The Wayne State University EcoCAR2 team provided its members with Modeling and Simulation training course for the second summer of the competition. EcoCAR2 is a three-year Advanced Vehicle Technology Competition (AVTC) sponsored by General Motors and the Department of Energy. The course lasted three months and included 45 hours of formal lectures and class hands-on work and an estimated one hundred and fifty hours in home assignments that directly contributed to the team's deliverables. The course described here is unique. The design and class examples were extracted from an in-house complete vehicle simulation and control code to ensure hands-on, interactive training based on real-world problems. The course investigated the physics behind every major powertrain component of a hybrid electric vehicle and the different ways to model the components into a full vehicle simulation.

Hybrid electric vehicles (HEV's) are facing increasing challenges in optimizing the energy flow through a vehicle system, in order to improve both fuel economy and vehicle emissions. Energy management of HEV's is a difficult task due to the complexity of the total system in terms of electrical, mechanical and thermal behavior. In this paper, an advanced control strategy for a parallel hybrid vehicle is developed. Four main steps are presented, particularly to achieve a reduction in fuel consumption. The first step is the development of a highly complex HEV model, including dynamic and thermal behavior. Second, a heuristical control strategy is developed to determine the HEV modes and third, a State of Charge (SoC) leveling is developed with the interaction of a fuzzy logic controller. It is proposed to calculate the load point shifting of the Internal Combustion Engine (ICE) and the desired battery SoC.

Biodiesel from non-edible vegetable oils is of paramount significance in India due to insufficient edible oil production. The present work deals with relatively underutilized non-edible oil “Schleichera oleosa” or “Kusum”. The Kusum biodiesel (KB) was produced using a two stage esterification cum transesterification process as the free fatty acid content of the oil was high. Important physico-chemical properties were evaluated and they were found to conform with corresponding ASTM/EN standards. Various test fuels were prepared for the engine trial by blending 10%, 20%, 30% and 40% of KB in diesel by volume and were named as KB10, KB20, KB30 and KB40 respectively. The results showed that full load brake thermal efficiency was dropped by 3.8% to 17% with increase in KB composition in the test fuel. Diesel (D100) showed the maximum full load brake specific energy consumption followed by KB10, KB20, KB30 and KB40.

Energy management system designs for road vehicle applications have for some time considered the use of road data geospatial attributes such as elevation, speed limits and GPS derived online information, like traffic and position, to forecast the amount of fuel that could be consumed by a given vehicle on a specific route. This approach is especially useful when dealing with electrified platforms as on-board energy storage devices (such as fuel cells or batteries) have a lower energy density ratio [kJ/g]. Unfortunately within the tactical mobility context such information might not be readily available, either by passive obstructions, like mountains, or active ones due to jamming, etc. This paper will elaborate on an energy management system meant to deal with the uncertainty created by navigating in terrain where only basic trip information is available, such as probable distance to be travelled.

Plug-in hybrid electric vehicles (PHEVs) with post-transmission parallel configuration attracted considerable attention due to their capacity to operate in either electric vehicle (EV) mode or hybrid electric vehicle (HEV) mode. Meanwhile, the added flexibility and multiple operation modes add additional challenges to vehicle control with acceptable drivability, particularly during the mode transition from the EV and HEV, since proper control is needed for the internal combustion engine (ICE), motor and coupling device to achieve smooth and fast transition, under various vehicle operation constraints such as mode-transition duration, vehicle acceleration fluctuation and friction loss of the dry clutch. In addition, the engagement of dry clutch features torque discontinuity due to slip-stick phenomenon and the dynamic behavior of the ICE further increases the nonlinearity of the powertrain system.

The domains of powertrain and brake systems are continuously merging due to the integration of electric drives and their ability to generate high acceleration and recuperative torque. However, high recuperative torque might lead to a locking motor and consequently cause a stability issue in electric and hybrid vehicles. This paper focuses on the special case of recuperation by coasting; i.e., the torque request is set after releasing the accelerator pedal. In this case the mechanical brake is not used. For off-highway vehicles this new feature in the inverter will suppress the slipping and locking up of the tires, without the need of additional external sensors. Slipping of the tires, e.g. when the tires lose grip, can occur due to excessive torque from the motor. In this case the motor torque exceeds the minimum feasible deceleration torque, given by road friction.

This paper presents an approach to numerically simulate greenhouse windnoise. The term “greenhouse windnoise” here describes the sound transferred to the interior through the glass panels of a series vehicle. Different panels, e.g. the windshield or sideglass, are contributing to the overall noise level. Attached parts as mirrors or wipers are affecting the flow around the vehicle and thus the pressure fluctuations which are acting as loads onto the panels. Especially the wiper influence and the effect of different wiper positions onto the windshield contribution is examined and set in context with the overall noise levels and other contributors. In addition, the effect of different flow yaw angles on the windnoise level in general and the wiper contributions in particular are demonstrated. As computational aeroacoustics requires accurate, highly resolved simulation of transient and compressible flow, a Lattice-Boltzmann approach is used.

Intake and exhaust system development is an important step in automotive design. The intake system must allow sufficient air to flow into the engine, and the exhaust system must allow exhaust gases to depart at the rear of the vehicle, without excessive pressure loss. These systems must also attenuate the acoustic pressure pulsations generated by the engine, such that the noise emitted from the intake and exhaust orifices is constrained within reasonable limits, and exhibits a sound quality in keeping with the brand and vehicle image. Pressure loss and orifice noise tend to be in conflict, so an appropriate trade-off must be sought. Simulation of both parameters allows intake and exhaust systems to be designed effectively, quickly, cheaply and promptly. Linear simulation approaches have been widely used for intake and exhaust acoustic prediction for many decades.

This paper presents new technique to estimate the projected operational forces, which is the operational forces with respect to the evaluation location, at the connections of the separated passive substructures with reciprocity. Since the transfer path analysis (TPA) is conducted with respect to the evaluation location, the forces for the substructures are, therefore, also required only to estimate the projected operational forces. In order to estimate the forces, the projected inertance matrix, which is the projection of the inertance matrix onto the subspace with respect to the evaluation location, is estimated without measuring it directly. The acceleration responses at the connections of the passive substructure are measured by the excitation at the evaluation location with the reciprocity. The technique decomposes the acceleration responses into the output and input element vectors on the subspace. With those vectors, the projected inertance matrix is constructed.

The optimal styling of the exterior surface of a vehicle and its suspension system have a direct impact on interior wind noise. Both are determined in early project phases when no hardware prototype is available. Turbulent flows produce both external pressure fluctuations at the vehicle shell, known as hydrodynamic excitation, and sound waves, known as acoustic excitation. Hydrodynamic and acoustic sound sources are evaluated separately and relative to each other in the frequency domain in order to perform evaluations of different body shapes. The technical aim of the presented work is to investigate how acoustic quantities measured at the outside of a vehicle can be used to assess the influence of styling modifications to interior sound pressure level. The methodology is required to be capable of being integrated into the serial development process and therefore be quickly applicable.

Transfer path analysis is a powerful tool to support the vehicle NVH development. On the one hand it is a fast method to gain an overview of the complex interplay in the vehicle noise generation process. On the other hand it can be used to identify critical noise paths and vehicle components responsible for specific noise phenomena. FEV has developed several tools, which are adapted to the considered noise phenomena: Powertrain induced interior noise and vibration is analyzed by VINS (Vehicle Interior Noise Simulation), which allows the deduction of improvement measures fast enough for application in the accelerated vehicle development process. Further on vehicle/powertrain combinations not realized in hardware can be evaluated by virtual installation of the powertrain in the vehicle, which is especially interesting in the context of engine downsizing from four to three or six to four cylinders.

The ELVA project (Advanced Electric Vehicle Architectures) was co-funded under the European Commission's 7th Framework Programme and had the goal of developing vehicle architectures specifically designed for electric powered vehicles. The consortium was formed by the Institute for Automotive Engineering (ika) of RWTH Aachen University (coordinator), Applus+ IDIADA, Volkswagen, Renault, Centro Richerche Fiat (CRF), Continental and the Swedish Vehicle and Traffic Safety Centre (SAFER).

Three wheeler taxis, commonly known as auto rickshaw are a popular means of transport in developing countries. However, low efficiencies and poor maintenance are common (especially in India). This results in high fossil fuel consumption, and very high urban air pollution due to these vehicles. Electrification of auto-rickshaw, therefore, is a potential solution to reduce dependence on fossil fuels, and reduce environmental pollution. However, this conversion is not straightforward. In this work, we investigate some of the challenges of converting an existing combustion engine powered auto-rickshaw to an electric auto rickshaw (electric vehicle (EV)). The cost of conversion to EV and sufficient charge storage capacity for driving range are important factors in the viability of such a conversion. The solution developed here is a design for low total ownership cost for short-range transport.

In the engine development process, the ability to judge NVH comfort as early as possible is a great benefit. The prediction of engine noise on the basis of a prototype engine without the need to install it in a real car significantly speeds up the development process and leads to a cost reduction, as prototype modifications can be evaluated faster. Meaningful predictions of the perceived NVH comfort cannot be achieved just by comparing order levels, but require listening to an auralization of the engine noise at the driver's position. With the methods of Transfer Path Analysis and Synthesis (TPA/TPS) a prototype engine can be virtually installed in a car using test-bench data. The interior noise can be estimated by combining source signals containing near-field airborne noise radiation and mount forces with transfer functions describing the transmission to the target position in the cabin.

The Aviation industry has come a long way since the invention of the aero-plane by the Wright Brothers. The shape and face of the industry has changed drastically since the time of its inception. With this paper, we intend to give a new perspective to the aviation industry. We try to do so by studying the aerodynamics of birds of prey, one of the most aerodynamically efficient examples created by nature. In this paper, we are publishing the results and inferences of Computational Fluid Dynamics (CFD) analysis on the 3D CAD model of a bird. The birds shortlisted for this exercise were the Red Tailed Hawk, the Peregrine Falcon and the Golden Eagle. The reason for this selection was their remarkable cruising speeds that reiterate the fact that they are natural examples of very high aerodynamic efficiency. Due to its larger size and availability of a clearer body size, shape and geometry, the Golden eagle was chosen as the final bird for analysis.

Since the last decade, the automotive industry has expressed the need to better understand how the different trim parts interact together in a complete car up to 400 Hz for structureborne excitations. Classical FE methods in which the acoustic trim is represented as non-structural masses (NSM) and high damping or surface absorbers on the acoustic cavity can only be used at lower frequencies and do not provide insights into the interactions of the acoustic trims with the structure and the acoustic volume. It was demonstrated in several papers that modelling the acoustic components using the poroelastic finite element method (PEM) can yield accurate vibro-acoustic response such as transmission loss of a car component [1,2,3]. The increase of performance of today's computers and the further optimization of commercial simulation codes allow computations on full vehicle level [4,5,6] with adequate accuracy and computation times, which is essential for a car OEM.

Dash panel is the most important path of structure-borne and air-borne interior noise for engine-driven vehicles. Reinforcements, which are added to dash panel, are mainly designed in order to suppress the structure-borne noise contribution from the dash panel. However, the effects of dash reinforcements do not seem clear in the viewpoint of air-borne noise. In this paper, the insulation performance of a dash structure with spot-welded reinforcements is studied through several STL (Sound Transmission Loss) tests and STL simulations. The results of this study could be utilized for increasing the sound insulation performance of vehicle body structure.

The driving comfort influences the customer purchase decision; hence it is an important aspect for the vehicle development. To better quantify the comfort level and reduce the experiment costs in the development process, the subjective comfort assessment by test drivers is nowadays more and more replaced by the objective comfort evaluation. Hereby the vibration comfort is described by scalar objective characteristic parameters that correlate with the subjective assessments. The correlation analysis requires the assessments and measurements at different vehicle vibration. To determine the objective parameters regarding the powertrain excitations, most experiments in the previous studies were carried out in several test vehicles with different powertrain units.

The advantages of hydraulic mounts over conventional elastomeric mounts for NVH refinement are well known, particularly in the area of engine and suspension mounts. Recently, hydraulic mounts have been successfully employed as body mounts between the frame and cab, principally to control freeway hop in pickup trucks. Due to their ability to provide increased damping at small displacements, hydraulic body mounts also have good potential to reduce smooth road shake. This paper documents the reduction in smooth road shake performance of a full size pickup truck. Hydraulic body mounts tuned to the frequency of the smooth road shake sensitivity area were added to the rearmost cab mount location. Both tire-wheel balance and uniformity were set to the highest production level specification allowed and the effect of hydraulic cab mount was measured experimentally during smooth road driving at medium to high speeds.