Search Results

The Ford GT Program Team was allocated just 22 months from concept to production to complete the Electrical and Electronics systems of the Ford GT. This reduced vehicle program timing - unlike any other in Ford's history -- demanded that the team streamline the standard development process, which is typically 54 months. This aggressive schedule allowed only 12 weeks to design the entire electrical and electronic system architecture, route the wire harnesses, package the components, and manufacture and/or procure all components necessary for the first three-vehicle prototype build.

This paper describes the rapid development of the Ford GT transmission, from concept phase to production, where the technical challenges involved are implicit in the specifications provided. It presents the steps taken at a project management level to expedite development, as well as the tools used to design and rate components at the design stage. Examples of concurrent engineering are given as well as management techniques used to predict and address key risks. In addition, details of analysis and test procedures are given, underlining their contribution to the rapid introduction of the transmission to the market place.

The objective of this paper is to compare the external anthropometry of 3 and 6 year old French children with the corresponding existing crash test dummies. An anthropometry study has been performed on about 70 (respectively 80) French children aged 3 years (respectively 6). More than 40 external measurements have been acquired on each subject. They include dimensions in standing and sitting positions: heights, lengths, circumferences, weight, etc. Mean, standard deviation, minimum and maximal values are given and compared with other existing international databases. From a global point of view, dimensions observed in this study appear 12% higher than in others. Dimensions are more specifically compared with corresponding crash test dummies in order to evaluate the validity of these anthropomorphic test devices.

Environmental Protection Agency (EPA) emissions standards for on-road heavy-duty diesel engines in 2007 will require the use of diesel particulate filters (DPF) to reach the regulated limit of 0.01g/bhp-hr for particulate matter. The inorganic portion of the particulate matter, referred to as ash, accumulates in the DPF over time with engine operation and periodic cleaning is necessary to remove the buildup. In anticipation of the required cleaning, flow bench testing and modeling were conducted for heavy-duty diesel DPFs to determine the effectiveness of compressed air nozzle cleaning and water cleaning. The result from this work shows that the first 10 minutes of cleaning removes greater than 55% of the filter soot/ash. Water cleaning was investigated and shows that it reduces filter pressure drop when repeated air cleaning was incapable of further reducing the pressure drop.

Diesel oxidation catalysts and particulate filters are recognized as proven solutions for reducing diesel emission levels. However, such systems now operate under extreme and unique conditions in order to meet even more demanding emission regulations. Long term cold holding performance, erosion resistance and high temperature stability are issues that must be addressed to assure a robust design in diesel oxidation catalysts and diesel particulate filters. This paper will describe the application of new concepts for support mat systems and results from internal lab testing. It will describe three different case histories, present the design parameters, and compare results with traditional support mat systems.

Tests of ultra-low sulfur diesel blended with soy-biodiesel at 5% and 20% were conducted using a 2002 model year Cummins ISB engine (with exhaust gas recirculation) that had been retrofitted with a passively regenerated catalyzed diesel particulate filter (DPF). Results show that on average, the DPF balance point temperature (BPT) is 45°C and 112°C lower for B20 blends and neat biodiesel, respectively, than for 2007 certification diesel fuel. Biodiesel causes a measurable increase in regeneration rate at a fixed steady-state condition, even at the 5% blending level. The data show no significant differences in NOx emissions for these fuels at the steady-state regeneration conditions, suggesting that differences in soot reactivity are responsible for the observed differences in BPT and regeneration rate.

Thermal shock performance parameters to assure Ultra Thin Wall (UTW) substrate durability for close-coupled (CC) converter operating conditions have been defined through testing and FEM modeling. Propane burner tests simulating the engine exhaust conditions were performed and coordinated with FEM stress analysis. For the stress analysis, a newly developed Macro-Micro Thermal Stress Analysis method was employed. Validation of the Macro-Micro Thermal Stress Analysis method was made through comparing FEM analysis results with the electric furnace and the burner tests results. A thermal fatigue life prediction method taking into account variation in material strength, fatigue degradation and effective volume was developed. In the verification tests, crack generation stresses were predicted within a 20 % margin of error.

Recently, catalyzed soot filters (CSF) for passenger vehicles have been introduced into the marketplace to comply with the European environmental requirements and future emission standards. The initial system consisted of one or two diesel oxidation catalysts (DOC) to meet the regulated HC and CO standards along with an under floor CSF to treat the particulate emissions. In order to meet the cold start requirements and to reduce system costs with a CSF only unit, converters are placed closer to the engine to minimize heat losses and more of the DOC functionality is integrated into the filter substrate. This work describes the development of such DOC-integrated CSF systems. One major challenge in the design of such systems is to ensure that there is sufficient catalyst functionality within the wall-flow substrate while maintaining an acceptable exhaust gas backpressure across the filter.

The “Range-of Motion of the Cervical Spine of Children” study is a collaboration between Kettering University and McLaren Regional Medical Center in Flint, Michigan to quantify and establish benchmarks of “normal” range of motion (ROM) in children. The results will be analyzed to determine mean and standard deviation of degrees of rotation and used to improve the occupant protection in motor vehicles, sports equipment and benefits of physical therapy. The data will be invaluable in the development of computational models to analyze processes involving children in motion.

Children who are too large for harness restraints but too small to obtain good restraint from a vehicle seatbelt alone should be seated in a belt-positioning booster. Boosters have been shown to significantly reduce abdominal injuries caused by seatbelts. This effectiveness may be due in part to the fact that boosters reduce the effective seat cushion length, allowing children to sit more comfortably without slouching. NHTSA recommends that children who do not use harness restraints use boosters until they are at least 145 cm tall. In this paper, data from several sources were combined to assess how well children fit on rear seat cushions. Data from NASS-GES were analyzed to determine the age distribution of rear-seat occupants. Anthropometric data from several sources were analyzed to determine the distribution of buttock-popliteal length, a measure of thigh length that is a key determinant of seat fit, as a function of age and gender.

Diesel Particulate active Reduction system (DPR) is a system that traps particulate matter in diesel exhaust gas with a particulate filter and actively regenerates the filter when PM accumulates to a specific level. In 2003, DPR was installed on Hino's light-, medium-, and heavy-duty diesel engines, and about 50,000 units of these DPR-equipped diesel engines are currently on the market. This paper reports results of further progress made on optimization of the active regeneration function of DPR. The goal of successful development of DPR is to optimally control the system under various engine-operating conditions to regenerate the filter without producing abnormal combustion of PM and to minimize the amount of unburned PM to keep the filter from clogging. To improve the control of DPR, the combustion phenomena of PM collecting on the filter were studied through visualization, and the factors influencing combustion were determined.

This paper presents a laboratory study of body dimensions, seated posture, and seatbelt fit for children weighing from 40 to 100 lb (18 to 45 kg). Sixty-two boys and girls were measured in three vehicle seats with and without each of three belt-positioning boosters. In addition to standard anthropometric measurements, three-dimensional body landmark locations were recorded with a coordinate digitizer in sitter-selected and standardized postures. This new database quantifies the vehicle-seated postures of children and provides quantitative evidence of the effects of belt-positioning boosters on belt fit. The data will provide guidance for child restraint design, crash dummy development, and crash dummy positioning procedures.

Several diesel passenger car manufacturers in the European Union recently announced the future use of catalyzed diesel particulate filter systems on their vehicles. The major technical challenge is the periodical regeneration of the filters loaded with the retained diesel particulates. In order to promote filter regeneration, catalytic activation of the accumulated soot is advantageous. Therefore, the first serial application of diesel particulate filter systems uses catalytically active fuel additives. These systems were introduced about four years ago. Since that time, other systems, using a dedicated catalytically activated diesel particulate filter combined with an upstream diesel oxidation catalyst, have been introduced as well. This allows filter regeneration without extra fuel additives. In the past, adding catalytic coating to a filter substrate has often resulted in increasing the pressure drop over the filter to an unacceptable level.

This paper reports on the desired performances for Catalyzed Soot Filters (Hereinafter referred as “CSF”), which is composed of a Diesel Particulate Filter (DPF) coated with an Oxidation Catalyst, its design factors and their influence on DPF performance, and on the lifetime prediction method to effectively design a DPF for durability. Performance means pressure drop, Particulate Matter (PM) regeneration limit, time for light-off, and canning strength. Design factors include cell structure, overall DPF size and material porosity. Knowing the relationships between performance and design factors assist the engineer in optimizing the selection of material, cell structure and size of the DPF.

It has been reported that particulate emissions from diesel vehicles could be associated with damaging human health, global warming and a reduction in air quality. These particles cover a very large size range, typically 3 to 10 000 nm. Filters in the vehicle exhaust systems can substantially reduce particulate emissions but until very recently it was not possible to directly characterise actual on-road emissions from a vehicle. This paper presents the first study of the effect of filter systems on the particulate emissions of a heavy-duty diesel vehicle during real-world driving. The presence of sulfur in the fuel and in the engine lubricant can lead to significant emissions of sulfate particles < 30 nm in size (nanoparticles).

DPF design, system integration, regeneration control strategy optimization and ash ageing assessment, based on a traditional design of experiments approach becomes very time consuming and costly, due to the high number of tests required. This provides a privileged window of opportunity for the application of simulation tools and hence simulation is increasingly being used for the design of exhaust after-treatment systems with a Diesel Particulate Filter (DPF). DPF behavior depends strongly on the coupling of physico-chemical phenomena occurring over widely disparate spatial and temporal scales and a state-of-the-art simulation approach recognizes and exploits these facts introducing certain assumptions and/or simplifications to derive an accurate but computationally tractable DPF simulation tool, for the needs of industrial users.

The IVT control system can be viewed as having two distinct roles, namely that of steady state and transient torque management. Steady state management functions consist of setting engine power and transmission reaction torque to achieve optimal fuel economy, emissions and driver demanded wheel torque. The transient torque management function defines additional engine and transmission reaction torques, based on known inertia and plant responses, to manage the transition between these steady state operating points according to the driver's wishes, subject to plant constraints. This paper gives a basic overview of the IVT steady state control functions, leading onto a detailed description of the transient torque management function. The software functions are illustrated in block diagram format, using simulation verification data plots and vehicle data logs for validation purposes.

This paper is a report of the findings and insights derived from a continuously variable transmission (CVT) research study. The research objective was to identify relationships between key CVT parameters and the customer perception of CVT performance. Four factors were studied: Ratio Schedule, Shift Speed, Dead Pedal, and Torque Converter Lock. Researchers evaluated the influence of these factors and their interactions on customer perception. Although one calibration is not significantly better than others, customers preferred three out of sixteen calibrations. DOE analysis shows flat ratio schedule to be statistically significant for Power and Pick-up. Several 2-way interactions are also statistically significant. Although a trade-off study must be completed to identify the best setting for a given vehicle, two calibration methods may be employed for higher customer satisfaction:

In order to reduce tail-pipe hydrocarbon emissions from SI gasoline engines, rapid catalyst warm-up and improvement of catalyst conversion efficiency are important. There are many reports which have been published by manufacturers and research institutes on this issue. For further reduction of tail-pipe hydrocarbon emissions, it is necessary to reduce engine-out hydrocarbon emissions and to improve after treatment, during the time the catalyst is not activated. This paper quantitatively analyzed the fuel amount of intake port and cylinder wall-wetting, burned fuel and engine-out hydrocarbon emissions, cycle by cycle in firing condition, utilizing a specially designed analytical engine. The effect of mixture preparation and fuel properties for engine-out hydrocarbon emissions, during the cold engine start and warm-up period, were quantitatively clarified.