Search Results

During the last years, a number of techniques aimed at the experimental identification of the knocking onset in Spark-Ignition (SI) Internal Combustion Engines have been proposed. Besides the traditional procedures based on the processing of in-cylinder pressure data in the frequency domain, in the present paper two innovative methods are developed and compared. The first one is based on the use of statistical analysis by applying an Auto Regressive Moving Average (ARMA) technique, coupled to a prediction algorithm. It is shown that such parametric model, applied to the instantaneous in-cylinder pressure measurements, is highly sensitive to knock occurrence and is able to identify soft or heavy knock presence in different engine operating conditions. An alternative, more expensive procedure is developed and compared to the previous one.

In order to improve fuel economy and available power, a knock detector system has been developed which controls the maximum charge pressure in the Saab 2-litre Otto Cycle Turbo engine. Compared to ignition retard knock control, the charge pressure control offers advantages in tolerance to variations in fuel octane number, full throttle fuel economy, hot spot auto ignition control, exhaust gas temperature and sensitivity to electrical noise and interference. Further, the system allows a significant temporary increase in available engine power when accelerating in normal traffic conditions. The turbocharger wastegate setting for maximum charge pressure is achieved through an integrated electronic system. The charge pressure knock control system is to a great extent “fail-safe”.

The effects of knock with varied intensity on spark-ignition engine performance and emission characteristics were investigated using a single-cylinder CFR engine operated by several different fuels. The variation of knock under a fixed engine speed was obtained by operating the engine using different octane numbers of the fuel and the variation of fuel's octane number was made as follows: For gasoline, two fuels having different octane ratings were used to obtain three different octane-number fuels, 85.3, 87.1, and 88.9; for gasoline/alcohol blend fuels, the volumetric alcohol contents in the blend were 0, 5, and 10% to obtain octane ratings of 85.3, 85.7 and 86.2, respectively; for natural gas (with over 94.5% methane by volume), small different amounts of alcohol were introduced into the stream of gas to produce octane numbers of 116, 118 and 120. For the same fuel, the knock intensity was stronger at lower engine speed and lower with high octane number.

The traditional philosophy that all knocking combustion is damaging has caused engine and fuel manufactures to operated with large “safety” margins, incurring both fuel production and consumption costs. This paper describes an attempt to relate knocking conditions to erosion damage. One of the goals was to discover a measurable knock intensity parameter which describes the propensity of knock to cause erosion damage. An experimental technique was developed in which test specimens were subjected to controlled knocking conditions in the combustion chamber of a modified engine. A photographic method was employed to measure the relative level of erosion on the test specimens. This methodology was used to determine the effect of fuel type and operating conditions on knock-induced erosion. It was confirmed that the geometry as well as the temperature played a considerable role in the damage mechanism.

This paper reports an investigation of knock detection in spark ignition (SI) engines using EEMD-Hilbert transform based on the engine cylinder block vibration signals. Ensemble Empirical Mode Decomposition (EEMD) was used to de-compose the signal and detect knock characteristic. Hilbert transform was used to analysis the frequency information of knock characteristics. The result shows that for cylinder block vibration signals, the EEMD algorithm could extract the knock characteristic (include light knock), and the Hilbert transform result shows that the instantaneous of knock characteristics concentrate in 5000-10000Hz. At last, the knock window is then determined, based on which a new knock intensity evaluation factor K is proposed, and the results show that, the parameter K is reasonable and effective.

Knocking is still one of today’s major limitations regarding efficiency-increasing measures for SI combustion engines. Due to the complex stochastic nature of the phenomenon, not only prediction and consideration within the engine development is of relevance. A further challenge is control of the phenomenon during engine operation, with the aim of maximizing the efficiency while preventing engine damage and maintaining the driver comfort. Conventional knock control is characterized by detecting knock events and subsequently adjusting the spark timing depending on whether knock was detected. This paper proposes a new knock control concept based on the prediction and direct control of the knock frequency, compared to the conventional reactive and indirect control of the knock frequency. For the prediction of the knock frequency, a calculation approach based on three different parameters is utilized.

Gasoline engines can be affected, under certain operating conditions, by knocking combustions, which can result in serious engine damage. Specific power and efficiency are influenced by factors such as compression ratio and spark advance regulation, that modify the combustion development over the crank angle: the trade-off between performance and the risk of irreversible damages is still a key factor in the design of both high-performance (racing) and low-consumption engines. New generation detection systems, especially based on ionization current technology, allow aggressive advance mapping and control, and future equipment, such as low-cost in-cylinder pressure transducers, will allow following that trend. Also HCCI (Homogeneous Charge Compression Ignition) engines need a sophisticated combustion monitoring methodology, since increasing BMEP levels in HCCI mode force the combustion to approach the knocking operation.

Gasoline engines can be affected, under certain operating conditions, by knocking combustions: this is still a factor limiting engines performance, and an accurate control is required for those engines working near the knock limit, in order to avoid permanent damage. HCCI engines also need a sophisticated combustion monitoring methodology, especially for high BMEP operating conditions. Many methodologies can be found in the literature to recognize potentially dangerous combustions, based on the analysis of the in-cylinder pressure signal. The signal is usually filtered and processed, in order to obtain an index that is then be compared to the knock threshold level. Thresholds setting is a challenging task, since usually indexes are not intrinsically related to the damages caused by abnormal combustions events. Furthermore, their values strongly depend on the engine operating conditions (speed and load), and thresholds must therefore vary with respect to speed and load.

Hydrogen-fueled Argon Power Cycle engine is a novel concept for high efficiency and zero emissions, which replaces air with argon/oxygen mixtures as working fluid. However, one major challenge is severe knock caused by elevated in-cylinder temperature resulting from high specific heat ratio of Argon. A typical knock-limited compression ratio is around 5.5:1, which limits the thermal efficiency of Argon Power Cycle engines. In this article, preliminary experimental research on the effect of water direct injection at late exhaust stroke is presented at 1000 r/min with IMEP ranging from 0.3~0.6 MPa. Results show that, with temperature-reducing effect of water evaporation, knock is greatly inhibited and the engine can run normally at a higher compression ratio of 9.6:1. Water injected at the exhaust stroke minimizes its reducing effect on the specific heat ratio of the working fluid during the compression and expansion strokes.

The knock intensity of an SI engine has been defined using the combustion chamber rate of pressure change. The instrumentation used to measure knock intensity is described. The knock intensity spectrum for a CFR engine operating over a range of engine conditions is presented to illustrate the use of the definition.

Turbulent Jet Ignition is an advanced spark-initiated pre-chamber combustion system for otherwise standard spark ignition engines. Combustion in the main chamber is initiated by jets of partially combusted (reacting) pre-chamber products which provide a high energy ignition source. The resultant widely distributed ignition sites allow relatively small flame travel distances enabling short combustion durations and high burn rates. Demonstrated benefits include ultra lean operation (λ≻2) at part load and high load knock improvement. This study compared the knock limit of conventional spark ignition and pre-chamber jet ignition combustion with reducing fuel quality in a modern PFI engine platform. Seven PRF blends ranging from 93-60 octane were experimentally tested in a stoichiometric normally aspirated single-cylinder research engine at 1500 rev/min and ~WOT (98 kPa MAP).

Knock limitations are investigated using natural gas, with diesel pilot ignition, as a fuel for the 3406 DI-TA Caterpillar diesel engine. Thermodynamic properties at TDC are generated by computer and compared with experimental results. Exhaust emissions are analyzed. A comparison is made of dual-fuel operation relative to diesel. Observations are made to determine the onset of knock. The onset of knock is characterized as a function of engine speed, load, inlet manifold temperature, and air-fuel ratio (A/F). The conditions at the onset of knock are determined using cylinder pressure data. The most efficient operating range is determined with knock avoidance as a prime parameter.

Knocking combustion limits the application of high compression ratios in gasoline engines and therefore obstructs the improvement of thermal efficiency. Predicting knock and knock limited spark advance (KLSA) can guide engine upfront design and optimization before the prototype is built. This study employed three-dimensional computational fluid dynamics (CFD) simulations coupled with an accurate and computation-efficient knock model to predict the KLSA of a turbocharged direct-injection spark-ignition engine. The knock model predicted the end-gas auto-ignition based on a Livengood-Wu (L-W) integral transport equation instead of directly using detailed chemical mechanisms, which was able to achieve a fast computation time. To keep the predictability, ignition delay data was calculated using zero-dimensional chemistry simulation and tabulated a priori, which was then used for CFD simulation on the fly.

Engine and vehicle manufacturers are facing increasing pressure from legislation to reduce vehicle emissions and deliver improved fuel economy. Significant reductions in carbon dioxide (CO2) emissions will need to be achieved to meet these requirements whilst also satisfying the more stringent forthcoming emissions regulations. This focus on techniques to reduce the tailpipe CO2, whilst also being able to operate over the whole map without the use of fuel enrichment for component protection, is increasing the interest in novel combustion technologies. The pre-chamber-based Jet Ignition concept produces high energy jets of partially combusted species that induce ignition in the main combustion chamber to enable rapid and stable combustion. The present study focusses on the potential of passive jet-ignition to enable increased output whilst maintaining stoichiometric operation through reduce knock sensitivity.

Exhaust gas recirculation (EGR) has been shown to enable efficiency improvements in SI engines through multiple different mechanisms, including decreasing the knock propensity at high load, which allows higher compression ratio. While many of the benefits of EGR are applicable to both low and high power density engines, including reductions in pumping work and improved specific heat ratio, the knock benefits and corresponding compression ratio increases have been limited to low power density naturally aspirated engines primarily intended for hybrid vehicle architectures. An earlier study [1] indicated that there may be a kinetic limitation for the ability of EGR to mitigate knock under these conditions, but that study only considered a small number of conditions. This investigation expands on that study while also providing data for model validation for the new light-duty combustion consortium from the U.S. Department of Energy: Partnership for Advancing Combustion Engines (PACE).

The possibility to mitigate the knock onset by means of a controlled coolant flow rate is investigated. The study is carried out on a small displacement, N.A. 4-valve per cylinder SI engine. The substitution of the standard belt-driven pump with an electrically driven one allows the variation of the coolant flow rate regardless of engine speed and permits, therefore, the adoption of a controlled coolant flow rate. The first set of experimental tests aims at evaluating the engine operating condition and the coolant flow rate, which are more favorable to the knock onset. Starting from this condition, subsequent experimental tests are carried out for transient engine operating conditions, by varying the coolant flow rates and evaluating, therefore, its effects on cylinder pressure fluctuations. In all the experiments, the spark advance and the equivalence ratio are controlled by the ECU according to the production engine map.

Engine knock is limiting the efficiency of spark ignition engines and consequently further reduction of CO2 emissions. Thus, an combustion process simulation needs a well working knock model to take this phenomenon into account. As knocking events result from auto-ignitions, the basis of a knock model is the accurate modeling of the latter. For this, the introduced 0D/1D knock model calculates the Livengood-Wu integral to estimate the state of the pre-reactions of the unburnt mixture and considers the two-stage auto-ignition of gasoline fuels, which occurs at specific boundary conditions. The model presented in this publication is validated against measurement data of a single cylinder engine. For this purpose, more than 12 000 knocking working cycles are investigated, covering extensively varied operating conditions for a wide-ranging validation.

For the simultaneous evaluation of the influence on engine knock of both chemical conditions and global operating parameters, a combined tool was developed. Thus, a two-zone kinetic model for SI engine combustion calculation (Ignition) was implemented into an engine cycle simulation commercial code. The combined model predictions are compared with experimental data from a single-cylinder test engine. This shows that the model can accurately predict the knock onset and in-cylinder pressure and temperature for different lambda conditions, with and without EGR. The influence of nitric oxide amount from residual gas in relation with knock is further investigated. The created numerical tool represents a useful support for experimental measurements, reducing the number of tests required to assess the proper engine control strategies.

Improvement of performance and emission of future internal combustion engine for passenger cars is mandatory during the transition period toward their substitution with electric propulsion systems. In middle time, direct injection spark ignition (DISI) engines could offer a good compromise between fuel economy and exhaust emissions. However, abnormal combustion and particularly knock and super-knock are some of the most important obstacles to the improvement of SI engines efficiency. Although knock has been studied for many years and its basic characteristics are clear, phenomena involved in its occurrence are very complex and are still worth of investigation. In particular, the definition of an absolute knock intensity and the precise determination of the knock onset are arduous and many indexes and methodologies has been proposed. In this work, most used methods for knock onset detection from in- cylinder pressure signal have been considered.

Octane requirements of late model vehicles were determined by trained knock raters and compared with those determined by customers. Average differences of independent distributions of customer and rater requirements were about 3 Research Octane Numbers/2 Motor Octane Numbers at part-throttle and 6 RON/4 MON at full-throttle and maximum octane requirement conditions. Five percent of the customers objected to knock when their cars were operated on fuel matching rater requirements, while 50 percent objected when using fuel 6 RON/4 MON lower. Another program is planned because differences between rater and customer octane requirements were greater than expected.