Search Results

The operating range in HCCI mode is limited by the excessive pressure rise rate and therefore high combustion induced noise. The HCCI range can be extended with turbocharging which enables increased dilution of the charge and thus a reduction of combustion noise. When the engine is turbocharged the intake charge will have a high temperature at increased boost pressure and can then be regulated in a cooling circuit. Limitations and benefits are examed at 2250 rpm and 400 kPa indicated mean effective pressure. It is shown that combustion stability, combustion noise and engine efficiency have to be balanced since they have optimums at different intake temperatures and combustion timings. The span for combustion timings with high combustion stability is narrower at some intake temperatures and the usage of external EGR can improve the combustion stability. It is found that the standard deviation of combustion timing is a useful tool for evaluating cycle to cycle variations.

In the port injected Spark Ignition (SI) engine, the single greatest part load efficiency reducing factor are energy losses over the throttle valve. The need for this throttle valve arises from the fact that engine power is controlled by the amount of air in the cylinders, since combustion occurs stoichiometrically in this type of engine. In WEDACS (Waste Energy Driven Air Conditioning System), a technology patented by the Eindhoven University of Technology, the throttle valve is replaced by a turbine-generator combination. The turbine is used to control engine power. Throttling losses are recovered by the turbine and converted to electrical energy. Additionally, when air expands in the turbine, its temperature decreases and it can be used to cool air conditioning fluid. As a result, load of the alternator and air conditioning compressor on the engine is decreased or even eliminated, which increases overall engine efficiency.

Unburned hydrocarbon (UHC) and carbon monoxide (CO) emission sources are examined in an optical, light-duty diesel engine operating under low load and engine speed, while employing a highly dilute, partially premixed low-temperature combustion (LTC) strategy. The impact of engine load and charge dilution on the UHC and CO sources is also evaluated. The progression of in-cylinder mixing and combustion processes is studied using ultraviolet planar laser-induced fluorescence (UV PLIF) to measure the spatial distributions of liquid- and vapor-phase hydrocarbon. A separate, deep-UV LIF technique is used to examine the clearance volume spatial distribution and composition of late-cycle UHC and CO. Homogeneous reactor simulations, utilizing detailed chemical kinetics and constrained by the measured cylinder pressure, are used to examine the impact of charge dilution and initial stoichiometry on oxidation behavior.

The present study investigates cold start at very low temperatures, down to −29 deg C. The experiments were conducted in an optical light duty diesel engine using a Swedish class 1 environmental diesel fuel. In-cylinder imaging of the natural luminescence using a high speed video camera was performed to get a better understanding of the combustion at very low temperature conditions. Combustion in cold starting conditions was found to be asymmetrically distributed in the combustion chamber. Combustion was initiated close to the glow plug first and then transported in the swirl direction to the adjacent jets. A full factorial study was performed on low temperature sensitivity for cold start. The effects of cooling down the engine by parts on stability and noise were studied. Furthermore, different injection strategies were investigated in order to overcome the limited fuel evaporation process at very low temperatures.

Researchers at the Powertrain Control Research Laboratory (PCRL) at the University of Wisconsin-Madison have developed a transient test system for single-cylinder engines that accurately replicates the dynamics of a multi-cylinder engine. The overall system can perform very rapid transients in excess of 10,000 rpm/second, and also replicates the rotational dynamics, intake gas dynamics, and heat transfer dynamics of a multi-cylinder engine. Testing results using this system accurately represent what would be found in the multi-cylinder engine counterpart. Therefore, engine developments can be refined to a much greater degree at lower cost, and these changes directly incorporated in the multi-cylinder engine with minimal modification. More importantly, various standardized emission tests such as the cold-start, FTP or ETC, can be run on this single-cylinder engine.

This study describes tests with a fast clocked multispark ignition system intended to improve the stability of inflammation during charge stratification. The advantage of this ignition system is the capability it provides to adjust the number of sparks, the duration of single sparks and the intensity of the primary current. The basic engine test parameters were first set in an optically accessible pressure chamber under conditions approximating an engine. Two strategies were examined to analyze their effect on inflammation in stratified charge mode. On the one hand, the multispark ignition (MSI) system allows implementing an intermittent spark sequence in the spark gap between the spark plug electrodes. On the other hand, precisely timed pulsing of spark energy into the plasma channel during charge motion can generate a very large deflection of the ignition spark.

A series hydraulic hybrid concept (SHHV) has been explored as a potential pathway to an ultra-efficient city vehicle. Intended markets would be congested metropolitan areas, particularly in developing countries. The target fuel economy was ~100 mpg or 2.4 l/100km in city driving. Such an ambitious target requires multiple measures, i.e. low mass, favorable aerodynamics and ultra-efficient powertrain. The series hydraulic hybrid powertrain has been designed and analyzed for the selected light and aerodynamic platform with the expectation that (i) series configuration will maximize opportunities for regeneration and optimization of engine operation, (ii) inherent high power density of hydraulic propulsion and storage components will yield small, low-cost components, and (iii) high efficiency and high power limits for accumulator charging/discharging will enable very effective regeneration.

Direct injection offers a large number of degrees of freedom, as it strongly influences the mixture stratification process. Experiments on a single cylinder research engine fuelled by H2, carried out at Argonne National Laboratory, showed the influence of injection parameters (timing and geometry) on engine efficiency and combustion stability. At low load, when a late injection strategy was performed, an unstable engine behavior was detected varying the injection direction. In order to optimize the mixture stratification process in DI H2 engines, it is important to understand the physics underlying the experimental results. A spatially resolved representation of the in-cylinder processes is a useful tool to properly set the injection parameters. Also, the knowledge of the pre-injection flow field is of added value in optimizing the injection process.

The present paper describes the first results of a cooperative research project between GM Powertrain Europe and Istituto Motori of CNR aimed at studying the impact of Fatty-Acid Methyl Esters (FAME) and gas-to-liquid (GTL) fuel blends on the performance, emissions and fuel consumption of modern automotive diesel engines. The tests were performed on the architecture of GM 1.9L Euro4 diesel engine for passenger car application, both on optical single-cylinder and on production four-cylinder engines, sharing the same combustion system configuration. Various blends of biodiesels as well as reference diesel fuel were tested. The experimental activity on the single-cylinder engine was devoted to an in-depth investigation of the combustion process and pollutant formation, by means of different optical diagnostics techniques, based on imaging multiwavelength spectroscopy.

Cyber-physical systems consisting of networks of interacting systems are often developed by distributed teams in a production environment. Processes, tools and work products supporting development of cyber-physical systems are continuously evolving through the different design phases. A growing trend to manage the development process has been the use of model-based development approaches. However, these approaches primarily use behavioral models to represent complex systems, rendering them inadequate to address collaborative and non-functional program requirements. This paper discusses an architecture-driven process that can address the challenges posed during the development of cyber-physical systems. Two key enabling technologies – the SAE AADL (Architecture Analysis and Design Language) and the IME (Integrated Modeling Environment) are leveraged in this process.

An aircraft environmental control system (ECS) is commonly designed for a cabin that has been divided into several thermal control zones; each zone has an air flow network that pulls cabin air over an isolated thermocouple. This single point measurement is used by the ECS to control the air temperature and hence the thermal environment for each zone. The thermal environment of a confined space subjected to asymmetric thermal loads can be more fully characterized, and subsequently better controlled, by determining its “equivalent temperature.” This paper describes methodology for measuring and controlling cabin equivalent temperature. The merits of controlling a cabin thermal zone based on its equivalent temperature are demonstrated by comparing thermal comfort, as predicted by a “virtual thermal manikin,” for both air-temperature and equivalent-temperature control strategies.

The RFID on Parts Project Team has recently completed and approved Spec 2000 Chapter 9, “RFID on Parts”. Once approved by the ATA e-Business Steering Group, this standard will allow for archiving and sharing part history information directly on RFID tags using the User Memory Bank. Using a structure similar to a File Storage System, this standard organizes tag data in a structured and indexed system so that information can be shared among all members of the supply chain. Now that high memory, passive tags are becoming available, when used in conjunction with the “RFID on Parts” standard, they make it possible to tag parts not just with an identification number, but with birth records, a full history of maintenance activities and user archives. Since end users and maintenance organizations will no longer need to rely solely on information retrieved from a centralized database, new processes and efficiencies can be realized.

At Boeing’s commercial aircraft production in Everett Washington, the organization that supplies parts to the factory floor (known internally as Company 625) is revising their methods. A new process will deliver parts in kits that correspond to the installation plans used by the mechanics. Several alternative methods are under review. The authors used simulation methods to evaluate and compare these alternatives. This study focuses on the category of parts known as standard fasteners (‘standards’). Through direct observation, interviews with experts, as well as time and motion study, the process flow of the kitting operation was mapped A simulation model was created using the simulation software ARENA to examine two scenarios: the current kitting operation in the factory cribs and the proposed centralization of kitting operation in the Company 625.

The Systems Engineering Relationship between Qualification, Environmental Stress Screening (ESS), and Reliability is often poorly understood: as a consequence resources are expended on efforts that degrade inherent hardware reliability and vitiate reliability predictions. This article expatiates on the Systems Engineering relationship between Qualification and ESS, and how their proper application enhances inherent reliability and supports credible reliability predictions. Examples of how their uninformed application degrades inherent hardware reliability and vitiates reliability predictions, and how program/equipment managers can avoid this, are presented.

In this paper, manufacturing hollow cylindrical tank was demonstrated with gas forming of titanium sheets. An innovative gas blow forming method to produce a complex shape of hollow cylindrical tank from titanium multi-sheets by low hydrostatic pressure was presented. Finite element analysis on gas blow forming process has been carried out in order to improve the forming process when manufacturing subscale hollow cylinder structure using Ti-6Al-4V multi-sheets. The simulation focused on the reduction of forming time and obtaining final required shape throughout investigating the deformation mode of sheet according to the forming conditions and die geometry. The result shows that the manufacturing method with gas forming of multi-sheets of titanium alloy has been successful for near net shape forming of subscale hollow cylindrical tank of ramjet engine.

The applicability, interpretation, and implementation of the testing requirements, in various aerospace and military tubing material specifications have caused confusion across the tubing industry. Despite the release of AMS specifications, procurement entities continue to purchase material produced to the older and often cancelled Mil-T specifications. In addition to mechanical properties, these specifications cover requirements including composition, grain size, heat treating, passivation, pressure testing, formability, non-destructive testing, and sampling frequency. Confusion may result for tubing producers who also supply commercial grade tubing having similar mechanical properties aerospace tubing. Ultimately it is the responsibility of the tubing manufacturer to understand the risks involved in meeting the requirements of the aerospace material specifications, both Military and AMS.

A comparative study on engine performance and emissions (NOx, soot) formation has been carried out for the Volvo D12C diesel engine fueled by Rapeseed Methyl Ester, RME and conventional diesel oil. The fuel and combustion models used in this paper are the modifications of those described in [1–3]. The numerical results for different load cases illustrate that for both fuels nearly 100% combustion efficiency was predicted; in the case of RME, the cumulative heat release was compared with the RME LHV, 37.2 kJ/g. To minimize soot and NOx emissions, 25–30% EGR levels depending on the engine loads and different injection timings were analyses. To illustrate the optimal engine performance conditions, a special technique based on the time-transient parametric ϕ-T maps [4] has been used.

Recently, a tendency is consolidating to produce low displacement turbocharged spark-ignition engines. This design philosophy, known as “engine downsizing”, allows to reduce mechanical and pumping losses at low load as a consequence of the higher operating Brake Mean Effective Pressure (BMEP). The presence of the turbocharger allows to restore the maximum power output of the larger displacement engine. Additional advantages are a higher low-speed torque and hence a better drivability and fun-to-drive. Of course, at high loads, the spark-advance must be carefully controlled to avoid the knock occurrence and this determines a substantial penalization of the fuel consumption. The knowledge of the knock-limited spark timing is hence a key point in order to reduce the fuel consumption drop at high loads.

A detailed analysis of knocking events can help improving engine performance and diagnosis strategies. The paper aim is a better understanding of the phenomena involved in knocking combustions through the combination of CFD and signals analysis tools. CFD simulations have been used in order to reproduce knock effect on the in-cylinder pressure trace. In fact, the in-cylinder pressure signal holds information about waves propagation and heat losses: for the sake of the diagnosis it is important to relate knock severity to knock indexes values. For this purpose, a CFD model has been implemented, able to predict the combustion evolution with respect to Spark Advance, from non-knocking up to heavy knocking conditions. The CFD model validation phase is crucial for a correct representation of both regular and knocking combustions: the operation has been carried out by means of an accurate statistical analysis of experimental in-cylinder pressure data.

Liquid atomisation is an important technical field for a wide range of engineering and industrial applications, particularly in the field of internal combustion engines. In these engines, in fact, the amount of pollutants at the engine-out interface is directly related to the quality of the combustion process, which is in turn determined by the quality of the air-fuel mixture preparation in Direct Injection (DI) engines. As a consequence numerical-experimental research is crucial to their development. Despite the significant amount of research that has been carried out on DI engines simulation, breakup modelling is still a challenge. In this paper we present a new numerical model for multiphase flows that could be particularly suited for liquid jet and droplet breakup simulation. The model is based on a Lattice Boltzmann (LB) solver coupled to a higher order finite difference treatment of the kinetic forces arising from non-ideal interactions (potential energy).