Search Results

For more than 30 years, field research and laboratory testing have consistently demonstrated that properly wearing a seat belt dramatically reduces the risk of occupant death or serious injury in motor vehicle crashes. In severe rollover crashes, deformation to vehicle body structures can relocate body-mounted seat belt anchors altering seat belt geometry. In particular, roof pillar mounted shoulder belt anchors (“D-rings”) are subject to vertical and lateral deformation in the vehicle coordinate system. The ROllover Component test System (ROCS) test device was utilized to evaluate seat belt system performance in simulated severe rollover roof-to-ground impacts. A mechanical actuator was designed to dynamically relocate the D-ring assembly during a roof-to-ground impact event in an otherwise rigid test vehicle fixture. Anthropomorphic test device (ATD) kinematics and kinetics and seat belt tensions were compared between tests with and without D-ring relocation.

This study was conducted to explore the effect of various combinations of seatbelt-related safety components (namely, retractor pretensioners and load limiting retractors) on the adult rear passenger involved in a frontal collision. The study was conducted on a 50th Male and a 5th Female Hybrid III ATD in the rear seat of a mid-sized sedan. Each ATD was seated in an outboard position with 3-point continuous lap-shoulder belts. On these belts were combinations of pretensioners and load limiters. Since the main objective of this test series was to cross-compare the seatbelt configurations, front seats were not included in the buck in order to avoid uncontrollable variables that would have affected the comparison study if the possibility of contact with the front seat were allowed. Nevertheless, there was a short barrier devised to act as a foot-stop for both ATDs.

This work is part of a series of studies developed by the author. It is intended to systematically address the study and definitions of advanced concepts for the development of automotive design with a focus on Vehicle Definition (VD) and Occupant Packaging (VOP). The methodology presented here is based on the concepts of Knowledge-Based Engineering (KBE) that captures consolidated engineering knowledge that is repeatable, reusable, and noncreative. KBE’s goal is to optimize engineering tools in pursuit of best practices and performance gains, reducing time and cost. This methodology proposes the creation of a three-dimensional (3D) digital model using a Computer-Aided Design (CAD) tool, which will be called here the CAD KBE template. This model is in line with neural network technology that mimics the brain’s own problem-solving process, and every single template will be organized interdependently with other templates.

For the launch of the redesigned Lexus LS, a new 3.5 L V6 twin turbo engine has been developed aiming at unparalleled performance on four axes, “driving pleasure”, “power-performance”, “quietness” and “fuel economy”. To achieve outstanding power-performance and high thermal efficiency, the specifications have been optimized for high speed combustion. The maximum torque of 600 Nm, power of 310 kW (yielding specific power of 90 kW/L), and the maximum thermal efficiency of 37% have been achieved using several new technologies including a high efficiency turbocharger. A prototype vehicle equipped with this engine and Direct-Shift 10AT achieved a 0-60 mph acceleration time of 4.6 sec, with extremely good CAFE combined fuel economy of 23 mpg and power-performance aligned with V8 turbocharged offerings from competing OEM’s.

Vehicle localization and position determination is a major factor for the operation of Autonomous Vehicle. Errors or unavailability of resources to determine this, poses a serious threat not only to the vehicle but also the environment around it. Global Positioning System (GPS) is one of the most common resources to determine position about the reference geographic coordinate system. But this resource has several drawbacks of its own viz. clock errors, multi-path errors and also uncertainty of good signal strength due to weather conditions or physical barriers. Also an additional drawback of a low-update rate makes it unreliable for the Autonomous Localization algorithm to operate on this. Thus a system is required which has no external environment dependencies to determine the position of the vehicle. Inertial Measurement Unit is a coupled system comprising of a 3-axis accelerometer and 3-axis gyroscope which records body force accelerations and the yaw rate.

Event data recorders (EDRs) were harvested and imaged after Insurance Institute for Highway Safety (IIHS) 56 km/hr frontal and 64.4 km/hr frontal offset crashes of 15 different brands of 2016-2022 vehicles. The speed and delta-V in the EDR were compared to reference instrumentation. Speed data was accurate within the generally accepted range of +/-4%. The 40% overlap tests had generally similar vehicle kinematics, and their delta-Vx data was accurate. However, there was a much greater variance in the small (25%) overlap tests. Some outliers in the small overlap delta-Vx tests required further analysis using overhead video analysis. The video analysis more closely matched the EDR recorded values. These offset tests create significant post-crash rotation, and both EDR and IIHS instrumentation were affected by their location away from the center of gravity. The Y-axis was affected much more than the X-axis.

The objective of this experimental investigation was to analyze the effect of various exhaust gas aftertreatment technologies on particulate number emissions (PN) of an MPFI EU5 motorcycle. Specifically, three different aftertreatment strategies were compared, including a three-way-catalyst (TWC) with LS structure as the baseline, a hybrid catalyst with a wire mesh filter, and an optimized gasoline particulate filter (GPF) with three-way catalytic coating. Experimental investigations using the standard test cycle WMTC performed on a two-wheeler chassis dynamometer, while the inhouse particulate sampling system was utilized to gather information about size-dependent filtering efficiency, storage, and combustion of nanoparticles. The particulate sampling and measuring system consist of three condensation particle counters (CPCs) calibrated to three different size classes (SPN4, SPN10, SPN23).

The proposed Euro 7 emission standard foresees that the emission behaviour of Euro 7 vehicles is monitored via an on-board monitoring (OBM) system. In Euro 7 vehicles, OBM systems will monitor the emissions of nitrogen oxides (NOX), ammonia (NH3) and particulate matter (PM) for every trip through a combination of measured and modelled data. Sensors employed to support on-board diagnostics (OBD) in current vehicles may be used to support OBM. According to the Euro 7 OBM concept presented in this paper, OBM will serve a dual purpose: the first is to warn the user of a vehicle about the need to perform repairs on the engine or the pollution control systems when these are needed. If these repairs are not performed in a timely manner, the OBM system will be able to ultimately prevent engine restart, akin to the existing low-reagent driver warning system in some compression ignition vehicles. The second purpose of OBM is to monitor the compliance of vehicle types with the emission limits.

Successful development of a product requires the consideration and balancing of many design parameters. Proposals to modify designs that have been fully implemented and put into production are often made by people who were not involved in the original design process. Such proposals, commonly focusing on a specific aspect of the product, must be evaluated in the context of the overall product and its intended use by consumers; a design change may improve performance in one area but compromise performance in another, or even introduce new problem areas. As a case in point, several proposals have been made for operator protection systems with the claim that they would reduce the frequency and severity of injuries associated with All Terrain Vehicle (ATV) operation. For example, Johnson, Carpenter, Wright & Nelson (1991) considered selected accident modes and proposed a set of design changes involving a rollover protection system (ROPS) and significant vehicle modifications.

As reported by Wright and Carpenter (1) and others, the number of accidents resulting in serious injuries and deaths associated with All Terrain Vehicle (ATV) use increased dramatically during the 1980s. It was decided that a safer, more stable ATV should be and could be built. Three-wheel and four-wheel ATVs were considered. Two three-wheel ATVs and a four-wheel ATV were modified and fabricated as prototypes. While improvements of the three-wheel ATVs were realized, there were still considerable stability problems that could not be sufficiently corrected. The four-wheel prototype, denoted as RCX 250 (roll cage experimental vehicle with a 250 cc engine), demonstrated feasibility with clear improvements in safety. Analysis of the dynamics of the RCX 250 along with the description of the features and the test results are discussed.

Injury reconstruction is a process of injury analysis which combines both medical and engineering technology to produce a composite picture of injury causation. The process is outlined and the potential applications of this analysis are detailed.

A method is proposed for simulating the effects of dimensional variation from geometric dimensioning and tolerancing (GD&T) specifications. The method converts GD&T specifications into equivalent covariance matrices which are needed in the statistical simulation of random processes. Examples are given to show how the method can be implemented.

The last few years have witnessed a steadily increasing growth in the sales and use of three and four wheel all-terrain recreational vehicles (ATVs). These vehicles are promoted for off-road use and are operated in widely varied environments ranging from dry desert surfaces to wet hilly wooded areas of the country. The design of the ATV and its intended purpose make it an attractive vehicle for a large cross-section of the general public. The general appearance of the vehicle suggests a relatively simple and safe means of transportation, even in environments which have heretofore had limited accessibility. However, it appears that the design and operational characteristics of these vehicles require more of a driver than he may initially assume as evidenced by the number of injuries and deaths that have occurred. How can the number of deaths be reduced and the severity of injuries be lessened?

In vitro biomechanical studies were conducted on fresh human cadaveric thoracolumbar spines to establish the limits of tolerance, explain the mechanism of failure, and investigate the effects of improvement in strength and stability of the injured column using Harrington distraction rods, Luque rods and modified Weiss springs. Quasistatic axial tensile loading on ligaments, compressive loads on vertebra) bodies and intervertebral discs, and flexure and compression-flexion force vectors on ligamentous columns, intact torsos and injured spines were applied to delineate the biomechanical and functional patho-anatomic characteristics. Vertical drop tests were conducted with the Hybrid II manikin to predict the forces and accelerations on the vertebral column.

Serious injuries are caused to the chest and thoracic organs both in front and side automobile collisions, and statistical surveys indicate that overall chest injuries are the third most frequent after head and the lower limbs. For safer design of restraint systems and vehicle interiors experimental data has to be obtained to establish chest injury criteria. Unembalmed human cadavers were used to conduct nine frontal and fourteen lateral impacts including four with a simulated arm rest. All impacts used a six inch (15.2 cm) diameter impactor with impact velocities ranging from 12 mph (19.3 kph) to 20 mph (32.2 kph). Chest impacts were also conducted on rhesus monkeys and baboons to establish primate-human injury scaling criteria. Four human volunteers were used to obtain static load deflection curves in the lateral and frontal directions. The results of the above experiments and those conducted by other investigators are presented and analyzed.

All-Terrain Vehicles, usually called ATVs, are small motorized vehicles operating on three, four, or five low-pressure, high flotation tires that are “designed” for off-road use on a variety of terrains. As the use of these ATVs increased through the 1980's, the number of accidents resulting in serious injuries and deaths associated with A N use increased dramatically. The U.S. Consumer Product Safety Commission (CPSC) along with other surveys have estimated that one out of every 25 ATVs being used will be involved in an accident requiring professional medical attention. These problems led to the federal government working out an agreement with the major manufacturers of these vehicles. One aspect of the agreement was that there would be safety and stability standards that all ATVs would have to meet to be sold in this country.

The effect of frame flexibility on the stability of constant speed, straight line motions of a motorcycle is studied by reference to linearized differential equations governing the behavior of a system of five rigid bodies, two of which are connected to each other with a hinge, a spring, and a damper, and are intended to represent a flexible frame, while the rest represent the front fork and the wheels of the vehicle. Although the configuration of the system is characterized by seven generalized coordinates, it is shown that the stability information of interest can be deduced from four first-order differential equations.

Designing trucks for good ride characteristics is a challenge to the engineer, given the many design constraints imposed by requirements for transport productivity and efficiency. The objective of this lecture is to explain why trucks ride as they do, and the basic mechanisms involved. The response of primary interest is the vibration to which the driver is exposed in the cab. Whole-body vibration tolerance curves give an indication of how those vibrations are perceived at the seat; however, ride studies have shown that visual and hand/foot vibrations are also important to the perception of ride in trucks. The ride environment of the truck driver is the product of the applied excitation and the response properties of the truck. The major excitation sources are road roughness, the rotating tire/wheel assemblies, the driveline, and the engine.

To shape future mobility MAHLE has committed itself to foster wireless charging for electrical vehicles. The standardized wireless power transfer of 11 kW at a voltage level of 800 V significantly improves the end user experience for charging an electric vehicle without the need to handle a connector and cable anymore. Combined with automated parking and autonomous driving systems, the challenge to charge fleets without user interaction is solved. Wireless charging is based on inductive power transfer. In the ground assembly’s (GA) power transfer coil, a magnetic field is generated which induces a voltage in the vehicle assembly (VA) power transfer coil. To transfer the power from grid to battery with a high efficiency up to 92% the power transfer coils are compensated with resonant circuits. In this paper the Differential-Inductive-Positioning-System (DIPS) to align a vehicle on the GA for parking will be presented.