Search Results

The articulated frame steering (AFS) systems are widely implemented in construction, forestry and mining vehicles to achieve enhanced maneuverability and traction performances. The kinematic and dynamic performances of articulated steered vehicles are strongly influenced by properties of the frame steering system. In this paper, a flow volume regulated frame steering system is described and analytically modelled. The analytical model of the steering system is formulated in conjunction with yaw-plane model of a 35 tonnes mining vehicle to investigate steady as well as transient responses of the steering system and the vehicle. A field test program was undertaken to measure responses of the steering system and the vehicle under nearly constant speed turning as well as path-change maneuvers.

With mounting pressure on Indian manufacturers to meet future fuel economy and emissions mandates-including the recently passed Corporate Average Fuel Consumption (CAFC) standards for light-duty vehicles-many are evaluating new technologies. However, to provide an economically sustainable solution, these technologies must increase efficiency without increasing cost. One promising solution to meet both current, and future, standards is the opposed-piston engine. Widely used in the early 20th century for on-road applications, use of the opposed-piston engine waseventually discontinued due to challenges with emissions and oil control. But advancements in computer-aided engineering tools, combined with state-of-the-art engineering practices, has enabled Achates Power to develop a modern opposed-piston diesel engine architecture that is clean, significantly more fuel efficient and less expensive to manufacture than today's four-stroke engines.

Used oil analysis plays an important role in the field of engine development, considering that it can give brief idea about performance of lubricant/ oil being used, its compatibility with the system under considerations. At present, regular testing is done like elemental analysis using Inductive Coupled Plasma (ICP) which can give idea about wear elements and additive elements. But it does not give information on morphological characterization of particles. In present work, Environmental Scanning Electron Microscopy technique with EDAX detector is used for characterizing the used oil. Oil is filtered on suitable paper and the particles collected on paper are analyzed. This gives the information on morphology and size of particles, their elemental analysis and mapping so that the sources can be judged. Size of wear metal particle is very important factor as even few bigger size particles are more detrimental than large number of smaller particles.

The performance of internal combustion engines should be improved depending on some technological requirements and rapid increase in the fuel expenses. On the other hand, the improvements in engine materials are forced by using alternative fuels and environmental requirements. Therefore, the performances of engine materials become increasingly important. Experimental research of insulated diesel engine incorporating thermal barrier coating (TBC) has produced controversial result. Some publications report that engine efficiency increases with insulation, while others argue that efficiency decreases. There are reports also presenting a mixed picture. This Paper presents comparative analysis of heat release in base line and insulated (Piston crown with plasma sprayed zirconia coating) diesel engine. The coating system affects the fuel consumption, the power and the combustion efficiency, pollution contents and the fatigue lifetime of engine components.

Mechanical and wear properties of Al alloyed gray cast iron (0.5% and 1.0%) were compared with that of Mo (1.0%) and Cu (0.77%) alloyed gray cast iron in this investigation. All the alloys showed pearlitic microstructure. The graphite morphology varied due to varying chemistry. The fracture surface showed “cabbage” like dimpled morphology indicating the predominant ductile fracture. It was found that the Mo containing cast iron show 25 to 30% higher strength and 6 to 7 times better wear resistance compared to Al containing cast irons. The worn surface showed oxide formation during sliding.

Brake drum is an important component in automotive, which is a link between axle and wheel. It performance is of utmost importance as it is related to the safety of the car as well to the passengers. Many design parameters are taken into consideration while designing the brake drum. The sensitivity of these parameters is studied for optimum design of brake drum. The critical parameters in terms of reliability, safety & durability could be the cross section, thickness of hub, interference & surface roughness between bearing and hub, wheel loading, heat generation on drum, manufacturing and assembly process. The brake drum design is derived by considering these parameters. Hence the sensitivity of these parameters is studied both virtually & physically, in detail. The optimum value of each parameter could be chosen complying each other's values.

A turbocharger unit mainly consists of a centrifugal compressor and a turbine coupled together by a solid shaft. This is employed to boost the charge air pressure of the engine. Turbocharging in modern diesel and gasoline engines have become a common and essential operation to result higher power outputs, lower emissions, improved efficiency and refinements from a similar capacity of naturally aspirated engines. The automotive turbocharger system is a source of synchronous and asynchronous noises that should be eliminated or reduced for passenger comfort. Subjectively, a high whistle noise was audible in the passenger cabin during in a mid-rpm range drive in all gears in a 4 cylinder diesel vehicle. Objective noise and vibration data confirm the issue as unbalance whistle. A detailed study has been carried out to identify the source and radiating part of the unbalance whistle noise generated in a 4 cylinder diesel engine running a passenger car.

This paper is an attempt to compile a systematic approach which can be easily incorporated in the product development system used in the design and development of parking brake systems for passenger cars having rear drum brakes, which in turn can effectively reduce the lead time and give improved performance. The vehicle GVW, percentage gradient and maximum effort limits (as per IS 11852 - Part 3), tire and drum brake specifications were taken as front loading. This data is used for target setting of functional and engineering parameters, such as lever pull effort, lever ratio and angular travel of lever. Design calculations were performed to obtain theoretical values of critical parameters like lever effort and travel. The comparison between target and theoretical values give the initial confidence to the system engineer. Further, the outcome was taken to conceptualize the hard points of lever on vehicle for ergonomics.

Commercial vehicle plays an important role during transportation process under the demand of high speed, convenience and efficiency. So improving active safety of commercial vehicle has become a research topic. Due to the fact that braking characteristic is the basic and most closely related to safe driving of vehicle's performances, this paper aims to improve the braking performance by researching into an integrated control method based on the mature ABS products. Firstly, a strategy which gives priority to ABS and differential yaw moment control, complementary with the hydraulic active suspension control is proposed. In comparison with ABS, the combined control of brake system and suspension system is designed not only for preventing wheels lock. But the directional control to avoid roll or spin is more focused on. Then in order to run the novel method correctly, the controlled variables and evaluation criteria are illustrated briefly.

Gear noise and vibration in automobile transmissions is a phenomenon of great concern. Noise generated at the gearbox, due to gear meshing, also known as gear whine, gets transferred from the engine cabin to the passenger cabin via various transfer paths and is perceived as air borne noise to the passengers in the vehicle. This noise due to its tonal nature can be very uncomfortable to the passengers. Optimizing micro-geometry of a gear pair can help in improving the stress distribution on tooth flank and reducing the sound level of the tonal noise generated during the running of the gearbox when that gear pair is engaged. This technical paper contains the study of variation in noise level in passenger cabin and contact on tooth flank with change in micro-geometry parameters (involute slope and lead slope) of a particular gear pair. Further scope of study has been discussed at the end of the paper.

Curtain airbag design offers protection in side crash and it plays a critical role in safety of the vehicle. Curtain airbag provides protection to the occupant in many impact events like frontal offset, side barrier, and side pole and rollover condition. For a vehicle to be safe for any side impact condition, the curtain airbag should deploy and take its final shape before any injury happens to the occupant. During deployment, it is important that the airbag chooses a path of minimum resistance and does not get entangled in interior trims. In reality, the trims always do obstruct the path of airbag deployment in some way. Hence, special care has to be taken care for designing areas surrounding curtain like providing hinges, deflector components etc. to avoid being caught. There are about ten different factors on this deployment is dependent upon. This paper discusses these factors and the effect of the factors on the trims and airbag development.

During vehicle development, numerous test are done to ensure safety & durability of the vehicle. One such test prescribed by regulation (IS 12009:1995) is side door intrusion test (SDIT). This test evaluates strength requirement of a side door of passenger cars to minimize the safety hazards caused by intrusion into passenger compartment in a side impact accident viz., initial, intermediate and peak crush resistance. In current scenario the passenger car manufacturers are striving hard on cost reduction by reducing the development cost. Thus, to predict the exact vehicle performance before its prototype stage is vital. This can be achieved by evaluating performance by the help of Computer aided engineering (CAE) During the SDIT, the load is applied to the outer surface of the door in an inward direction. This inward force applied by loading device is resisted by the door assembly, while door is pivoted at door latch and hinge.

An interior sound quality is one of the major performance attribute, as consumer envisage this as class and luxury of the vehicle. With increasing demand of quietness inside the cabin, car manufactures started focusing on noise refinement and source separation. This demand enforces hydraulic power steering pump to reduce noise like Moan and Whine, especially in silent gasoline engine. To meet these requirements, extensive testing and in-depth analysis of noise data is performed. Structured process is established to isolate noises and feasible solutions are provided considering following analysis. a) Overall airborne noise measurement at driver ear level (DEL) inside the cabin using vehicle interior microphone. b) Airborne and Pressure pulsation test by sweeping pump speed and pressure at test bench. c) Waterfall analysis of pump at hemi anechoic chamber for order tracking and noise determination.

Expanding and improving road network in India has been a catalyst for increased use of road transport in both passenger and goods sector. With improved road quality, bigger commercials vehicles have entered the market. These provide a larger cabin area and better amenities in the truck driver cabin. One of the most welcome features is berths for lying down and sleeping. In most designs though, only the functionality of the berth has been taken into consideration. Safety of the occupants of the berths in the event of panic braking or collision of the vehicle, has not been given adequate consideration. In this work, design of such berths from occupant safety point of view has been assessed. Kinematics of occupants, sleeping in different typical postures, during frontal impact, has been simulated and resulting critical injury levels have been estimated. Based on this information, different arrangements of belts in “screen” type configuration were developed.

Fuel consumption, and the physical behaviours behind it, have never been of greater interest to the automotive engineering community. The enormous design, development and infrastructure investment involved with a new engine family which will be in production for many years demands significant review of the base engine fundamental architecture. Future CO2 challenges are pushing car manufacturers to consider alternative engine configurations. As a result, a wide range of diesel engine architectures are available in production, particularly in the 1.4 to 1.6 L passenger car market, including variations in cylinder size, number of valves per cylinder, and bore:stroke (B/S) ratio. In addition, the 3 cylinder engine has entered the market in growing numbers, despite its historic NVH concerns. Ricardo has performed a generic architecture study for a midsize displacement engine in order to assess the pros and cons of each engine configuration.

The abatement of nitrogen oxides emissions is a topic of major concern for automotive manufacturers. In addition to aftertreatment solutions such as LNT or SCR devices, the use of exhaust gas recirculation (EGR) is necessary in most of the applications to meet emissions regulations. Due to the high specific humidity of the exhaust gases, a high condensate flow may be generated if EGR gases are significantly cooled down. In the case of long-route EGR (LR-EGR) usage, this condensate flow would reach the compressor wheel. This paper explores the variables governing the condensation process and the potential effects of the liquid droplets and streams on the compressor wheel durability combining experimental and theoretical approach. For this purpose, visualization of both the condensate flow and the compressor wheel are performed. Tests are conducted in a flow test rig in which LR-EGR water content is reproduced by water injection on the hot air mass flow.

The focus on engine thermal management is rapidly increasing due to the significant effect of heat losses on fuel consumption, engine performance and emissions. This work presents a time resolved, high resolution 3D engine heat balance model, including all relevant components. Notably, the model calculates the conjugated heat transfer between the solid engine components, the coolant and the oil. Both coolant and oil circuits are simultaneously resolved with a CFD solver in the same finite volume model as the entire engine solid parts. The model includes external convection and radiation. The necessary boundary conditions of the thermodynamic cycle (gas side) are mapped from a calibrated 1D gas exchange model of the same engine. The boundary conditions for the coolant and at the oil circuits are estimated with 1D models of the systems. The model is calibrated and verified with measurement data from the same engine as modeled.

The limitation of fuel entry into the oil sump of an internal combustion engine during operation is important to preserve the tribological properties of the lubricant and limit component wear. For observation and quantification of the effects leading to fuel entry, a highly sensitive and versatile measurement system is essential. While oil sampling from the sump followed by laboratory analysis is a common procedure, there is no system for automatic sampling of all the positions and fast online analysis of the samples. For the research project ‘Fuel in Oil’, a measurement system was developed especially for the described tasks. The system is placed next to the engine in the test cell. Sampling points are the target point of the fuel injector jet and the liner below, the oil sump and the crankcase ventilation system.

Increased quantities of fuel in the lubricating oil of CI engines pose a major challenge to the automotive industry in terms of controlling the oil aging and the wear caused by dilution. Due to a lack of methods to calculate the oil-fuel-composite transport across the ring pack, predicting the fuel ratio in the oil sump has been an extremely challenging task for engine manufacturers. An accurate and computationally efficient simulation model is critical to predict the quantity of fuel diluted in the oil in the preliminary development stage of automotive engines. In this work, the complex composite transport across the piston ring pack was reduced to a simple transport model, which was successfully implemented into a multi-body simulation of the ring pack. The calculation domain was partitioned into two parts, the ring grooves and the piston lands. Inside the grooves the oil flow caused by the pumping and squeezing action of the piston rings was calculated using the Reynolds equation.

The emissions from a parallel hybrid combustion engine and electric powertrain operated on a modified New European Drive Cycle (NEDC) was investigated in order to determine the relation between emissions and the road and engine load profile. The effect of simulated electric motor assistance during accelerations on emissions was investigated as a means to reduce particulate and gaseous emissions. The time resolved particulate number and size distribution was measured in addition to gaseous emissions. The combustion engine was a downsized, three cylinder spark ignited direct injection (SIDI) turbocharged engine fuelled with gasoline. Electric motor assistance during accelerations was simulated by reduction of the vehicle mass. This reduced engine load during accelerations. Fuel rich engine transients occurred during accelerations. NOx emissions were reduced with electric assistance due to a reduction in engine load.