Search Results

A GE Aviation Systems report documents that the National Oceanic and Atmospheric Administration (NOAA) provided weather forecast data has a bias of 15 knots and a standard deviation of 13.3 knots for the 40 flights considered for the research. It also had a 0.47 bias in the temperature with a standard deviation of 0.27. The temperature errors are not as significant as the wind. There is a potential opportunity to reduce the operational cost by improving the weather forecast. The flight management system (FMS) currently uses the weather forecast, available before takeoff, to identify an optimized flight path with minimum operational costs depending on the selected speed mode. Such a flight plan could be optimum for a shorter flight because these flight path planning algorithms are very less susceptible to the accuracy of the weather forecast.

Scramjet-based hypersonic airbreathers are needed for next-generation defense and space applications. Two scramjet configurations, namely, rectangular and axisymmetric, are primarily studied in the literature. However, there is no quantitative comparison of the performance metrics between these two scramjet configurations. This study investigates the aero-thermo-structural performance of rectangular and axisymmetric scramjet engines at Mach 7 and 25 km altitude. A numerical framework involving computational fluid dynamics and computational structural dynamics is established. The aero-thermo-structural loads on the scramjet flow path are estimated using RANS/FANS simulation. A finite element-based coupled thermo-structural analysis is performed to understand the thermo-structural response. Before using the numerical models for the study, CFD and CSD modules are validated with literature data.

In a typical Launch Vehicle (LV), dynamic responses due to various flight events are estimated through Coupled Load Analysis (CLA) where the launch vehicle is coupled with a spacecraft. A launch vehicle is subjected to various loads during its flight due to engine thrust depletion / shut-off, thrust oscillation, wind and gust, maneuvering loads. In aerospace industry a standard CLA is performed by generating the mathematical model of launch vehicle and coupling it with reduced mathematical model of satellite and applying the boundary conditions. A CLA is a time consuming process as several flight instances and load cases need to be considered along with generation of structural dynamic model at each time instants. For every new mission, the satellites are mission specific whereas the launch vehicle and the loads remain unchanged. To take advantage of this fact, a new method called “Fast CLA through Reanalysis technique” is proposed in the present paper.

It is important to accurately predict the aerodynamic properties for designing applications which involves fluid flows, particularly in the aerospace industry. Traditionally, this is done through complex numerical simulations, which are computationally expensive, resource-intensive and time-consuming, making them less than ideal for iterative design processes and rapid prototyping. Machine learning, powered by vast datasets and advanced algorithms, offers an innovative approach to predict airfoil characteristics with remarkable accuracy, speed, and cost-effectiveness. Machine learning techniques have been applied to fluid dynamics and have shown promising results. In this study, machine learning model called the back-propagation neural network (BPNN) is used to predict key aerodynamic coefficients of lift and drag for airfoils.

With the present state of the art technology, size and mass of the satellites have come down. This necessitated the need for a low shock separation system that does not have mass attached to the separated satellite. Development of Nano satellites with mass of the order of 1 to 24 kg has become popular among scientific/ academic institutions for carrying out scientific experiments. INLS 3U Unipod System (Nano satellite dispenser system) is a satellite dispensing system designed by ISRO for accommodating four 3U class Nano satellites in a single structure where each satellite is deployed independently by separate actuation commands. INLS stands for ISRO's Nano satellite Launch System. The Unipod separation system successfully flown first time in PSLV C56 Mission for the deployment of three foreign satellites namely Nulion, Galassia-2 and SCOOB II.

In the architecture of an Unmanned Aerial Vehicle (UAV), a crucial component responsible for the propulsion system is the electric motor. Over the years, different types of electric motors, including Brushless Direct Current (BLDC), have supported the UAV’s propulsion system in diverse configurations. However, in the context of flux flow, the Radial Flux Permanent Magnet Motor (RFPMM) has been given more priority than the Axial Flux Permanent Magnet Motor (AFPMM) due to its sustainability in design and construction. Nevertheless, the AFPMM boasts higher speed, power density, lower weight, and greater efficiency than the RFPMM, because of its shorter flux path and the absence of end-turn winding. Therefore, this paper focuses on conducting a suitability analysis of an AFPMM as a shaft-connected propeller-mounted motor, with the intention of replacing the RFPMM in UAV applications.

This research employs a comprehensive methodology to explore hypersonic boundary layers' stability and transition dynamics, focusing specifically on the influence of sharp and blunt leading edges. The Stanford University Unstructured (SU2) Computational Fluid Dynamics (CFD) solver is utilized to compute the mean flow over a flat plate, establishing a foundational basis for subsequent stability analysis. The extracted boundary layer profiles undergo validation against existing literature, ensuring accuracy and reliability. Further analysis is conducted using a Python code to generate input files for the Linear Stability Solver. The Linear Stability Solver analysis constitutes a crucial phase wherein the research delves into the eigenvalue spectra, identifying dominant modes and closely scrutinizing the role of the modes in the transition process within the hypersonic boundary layers.

In recent decades, research based innovative system-on-chip (SoC) design has been a very important issue, due to the emerging trends and application challenges. The SoCs encompass digital, analog and mixed-signal hardware and software components and even sensors and actuators. Modelling and simulation constitute a powerful method for designing and evaluating complex systems and processes for many analysts and project managers as they engage in state of-the-art research and development. Modelling and simulations not only help them with the algorithm or concept realization and design feasibility, but it also allows experimentation, optimization, interpretation of results and validation of model.

Lunar tubes, natural underground structures on the Moon formed by ancient volcanic activity, offer natural protection from extreme temperatures, radiation, and micro-meteorite impacts, making them prime candidates for future lunar bases. However, the exploration of lunar tubes requires a high degree of mobility. Given the Moon's gravity, which is approximately six times weaker than Earth's, efficient navigation across rugged terrains within these lava tubes is achievable through jumping. In this work, we present the design of subsystems for a miniature hexapod rover weighing 1 kg, which can walk, jump, and stow. The walking system consists of two subsystems: one for in-plane walking, employing four single-degree-of-freedom (DOF) legs utilizing the KLANN walking mechanism, and another for directional adjustments before jumping. The latter employs a novel three-DOF mechanism employing a cable pulley mechanism to optimize space utilization.

The finite element method is one of the most robust tools in structural analysis. Typically, the input parameters in a finite element model are assumed to be deterministic. However, in practice, almost all material and geometrical properties, including the load, possess randomness. The consideration of the probabilistic nature of these quantities is essential to effectively designing a system that is robust against the uncertainties arising due to the variation in the input parameters, the significance of which has been documented by NASA in “Probabilistic Risk Assessment Procedures Guide for NASA Managers and Practitioners”, 2011. Among the various techniques applicable for stochastic analysis, the perturbation method, which is based on a sound mathematical foundation derived from Taylor’s series expansion, is widely acknowledged for its much higher efficiency compared to the well-known Monte-Carlo method.

This study presents the constructed electromechanical model and the analysis of the obtained nonlinear systems. An algorithm for compensating the nonlinear drift of a gyroscope in a microelectromechanical system is proposed. Tests were carried out on a precision rotating base, with the angular velocity changing as per the program. Bench testing the gyroscope confirmed the results, which were also supported by the parameter calibration. The analytical method was further validated through experimental results, and a correction algorithm for the mathematical model was developed based on the test results. After calibration and adjusting the gyroscope’s systematic flaws, the disparity in calculating the precession angle was within 1/100th of an angular second over an interval of approximately 1000 s. Currently, research is underway on the new nonlinear dynamic characteristics of electrostatically controlled microstructures.

This paper investigates the utilization of Low Earth Orbit (LEO) satellites for vehicle localization and conducts a comparative analysis with traditional Global Navigation Satellite Systems (GNSS)-based methods. With the rise of LEO satellite constellations, such as Starlink, LEO-based vehicle localization may offer solutions to GNSS-related challenges. With a large number of satellites and short communication distance, the LEO-based method has great potential to improve accuracy, reduce warm-up time, and provide a robust localization solution for vehicle applications. In this paper, a dedicated LEO satellite simulator is presented, adaptable to various LEO constellations, making it relevant for evolving technologies beyond older LEO systems like Orbcomm or Iridium. The simulator includes satellite trajectory generation, observable satellite identification, and vehicle localization.

Efficient and accurate ordinary differential equation (ODE) solvers are necessary for powertrain and vehicle dynamics modeling. However, current commercial ODE solvers can be financially prohibitive, leading to a need for accessible, effective, open-source ODE solvers designed for powertrain modeling. Rust is a compiled programming language that has the potential to be used for fast and easy-to-use powertrain models, given its exceptional computational performance, robust package ecosystem, and short time required for modelers to become proficient. However, of the three commonly used (>3,000 downloads) packages in Rust with ODE solver capabilities, only one has more than four numerical methods implemented, and none are designed specifically for modeling physical systems. Therefore, the goal of the Differential Equation System Solver (DESS) was to implement accurate ODE solvers in Rust designed for the component-based problems often seen in powertrain modeling.

This research focused on developing a methodology for a vehicle dynamics model of a passenger vehicle outfitted with an aftermarket Automated Driving System software package using only literature and track based results. This package consisted of Autoware.AI (Autoware ®) operating on Robot Operating System 1 (ROS™) with C++ and Python ®. Initial focus was understanding the basics of ROS and how to implement test scenarios in Python to characterize the control systems and dynamics of the vehicle. As understanding of the system continued to develop, test scenarios were adapted to better fit system characterization goals with identification of system configuration limits. Trends from on-track testing were identified and paired with first-order linear systems to simulate physical vehicle responses to given command inputs. Sub-models were developed and simulated in MATLAB ® with command inputs from on-track testing.

Autonomous driving technology is more and more important nowadays, it has been changing the living style of our society. As for autonomous driving planning and control, vehicle dynamics has strong nonlinearity and uncertainty, so vehicle dynamics and control is one of the most challenging parts. At present, many kinds of specific vehicle dynamics models have been proposed, this review attempts to give an overview of the state of the art of vehicle dynamics models for autonomous driving. Firstly, this review starts from the simple geometric model, vehicle kinematics model, dynamic bicycle model, double-track vehicle model and multi degree of freedom (DOF) dynamics model, and discusses the specific use of these classical models for autonomous driving state estimation, trajectory prediction, motion planning, motion control and so on.

Vehicle yaw stability control (YSC) can actively adjust the working state of the chassis actuator to generate a certain additional yaw moment for the vehicle, which effectively helps the vehicle maintain good driving quality under strong transient conditions such as high-speed turning and continuous lane change. However, the traditional YSC pursues too much driving stability after activation, ignoring the difference of multi-objective requirements of yaw maneuverability, actuator energy consumption and other requirements in different vehicle stability states, resulting in the decline of vehicle driving quality. Therefore, a vehicle yaw stability model predictive control strategy for dynamic and multi-objective requirements is proposed in this paper. Firstly, the unstable characteristics of vehicle motion are analyzed, and the nonlinear two-degree-of-freedom vehicle dynamics models are established respectively.

Brake pulsation is a low frequency vibration phenomenon in brake judder. In this study, a simulation approach has been developed to understand the physics behind brake pulsation employing a full vehicle dynamics CAE model. The full vehicle dynamic model was further studied to understand the impact of suspension tuning variation to brake pulsation performance. Brake torque variation (BTV) due to brake thickness variation from uneven rotor wear was represented mathematically in a sinusoidal form. The wheel assembly vibration from the brake torque variation is transmitted to driver interface points such as the seat track and the steering wheel. The steering wheel lateral acceleration at the 12 o’clock position, driver seat acceleration, and spindle fore-aft acceleration were reviewed to explore the physics of brake pulsation. It was found that the phase angle between the left and right brake torque generated a huge variation in brake pulsation performance.

Human driving behavior's inherent variability, randomness, individual differences, and dynamic vehicle-road situations give human-machine cooperative (HMC) driving considerable uncertainty, which affects the applicability and effectiveness of HMC control in complex scenes. To overcome this challenge, we present a novel data-enabled game output regulation approach for HMC driving. Firstly, a global human-vehicle-road (HVR) model is established considering the varied driver's steering characteristic parameters, such as delay time, preview time, and steering gain, as well as the uncertainty of tire cornering stiffness and variable road curvature disturbance. The robust output regulation theory has been employed to ensure the global DVR system's closed-loop stability, asymptotic tracking, and disturbance rejection, even with an unknown driver's internal state. Secondly, an interactive shared steering controller has been designed to provide personalized driving assistance.