Search Results

There is a strong interest around the world in natural gas as an alternative fuel. This paper is concerned with the option of converting diesel engines to spark ignition operation. Although this may appear to be an outrageous thermodynamic action, it is preferable to using natural gas in a low compression gasoline engine conversion. An investigation is described in which engine maps were produced for a 5.6 litre direct injection diesel engine converted to CNG. The diesel operating characteristics have been compared with those of the spark ignition conversion at compression ratios of 18:1 (the original diesel value), 15:1 and 13:1. Detailed data are presented for the 15:1 compression ratio. These test results are supplemented by results for other diesel conversions. The use of these engines in bus fleet operations is also discussed.

Many areas of the world are in various stages of development which frequently includes a rapid increase in the motor vehicle population. As a result, some areas are beginning to show the effect of increased motor vehicle use on air pollution. The vehicle's contribution to California's air pollution has long been recognized and studied, and measures have been implemented to reduce emissions from motor vehicles. The history of light duty vehicle emission control in the South Coast Air Basin of California is reviewed. Emission reductions achieved, current levels, projected future emissions and the need for further emissions reductions from light duty vehicles are discussed. For other areas of the world where motor vehicles contribute to air pollution, suggestions are made which can improve the effectiveness of emission control efforts; which should be consistent with political and economic realities, and efforts to achieve international harmonization of standards.

Motor vehicle standards in Japan was systematically established in 1951 for the first time. On the other hand, in Europe, the United States and Australia, etc., there are EEC directive, FMVSS and ADR, etc. However, it is desirable to harmonize these standards as harmonization of motor vehicle standards will contribute to the improvement of productivity for motor vehicle development and manufacture. As for the international harmonization, ECE WP29 has been playing a key role. Therefore, Japan has positively supported the standard harmonizing activities of ECE WP29. We must promote the international harmonization in co-operation with ECE WP29.

A survey of the in-service fuel consumption of passenger vehicles and derivatives in the Australian fleet was carried out in 1984-85. Seven hundred and four owners across Australia took part in the survey. Vehicle owners reported by questionnaire the amount of fuel used during four tank fills of normal operation, the distance travelled, and other details of the operating circumstances. The survey shows a clear downward trend in the fuel consumption of the Australian passenger fleet. The data also provides comparisons of actual fuel consumption obtained on the road, with laboratory derived values for fuel consumption. Vehicles in a sub-set of 40 were fitted with fuel flow meters during the survey and tested to Australian Standard 2077 for fuel consumption. The questionnaire method is shown to be a valid and accurate technique for determining in-service fuel consumption.

To improve the cold startability of methanol, methanol-butane mixed fuel was experimented. Engine performance and exhaust emissions are obtained with methanol-butane mixed fuel. These characteristics are compared with those of methanol and gasoline. The mixing ratios of methanol and butane are 50:50 (M50), 80:20 (M80), and 90:10 (M90) based on the calorific value. As a result, M90 produces more power than gasoline and more or less than methanol depending on the engine speed and the excess air ratio. Brake horse power of M90 is higher than that of gasoline by 5 - 10 %, and brake specific fuel consumption is smaller than that of gasoline by 17 % to the maximum based on the calorific value. NOx emission concentrations for M90 are lower than those for gasoline and higher than those for methanol because of the effect of butane, CO emission concentrations are somewhat lower than those for methanol and gasoline.

In order to achieve lean burn engine control system, it is necessary to develop high accuracy air fuel ratio control technology including transient driving condition and lean burn limit expansion technology. This paper describes the following. 1 The characteristics of the transient response of the fuel supply are clarified when various kinds of air flow measuring methods and fuel injection methods are used. 2 To achieve stable combustion in lean mixture, fine fuel droplet mixture, whose diameter is less than 40 μm, needs to be supplied.

Unsteady laminar flame propagation confined in a closed cylindrical combustion bomb is studied by numerical computation for an axisymmetric two-dimensional laminar flame. Computation includes complete two-dimensional unsteady Navier-Stokes equations of change for a chemically reacting propane-air mixture. Implicit Continuous fluid Eulerian, Arbitrary Lagrangian Eulerian finite difference technique, simplified reaction kinetics models, and artificial flame stretching transformation and inverse transformation were adopted in the calculation. Physically realistic flame behavior can be demonstrated even with rather coarse computing cell size, simplified reaction kinetics models, and personal computer level low power computing machines.

A procedure has been developed for evaluating equivalent drive cycle emission results from raw exhaust gas emissions data obtained from an engine under test on a computer controlled Vehicle Simulator Engine Dynamometer. The emitted species data is integrated with the air intake flow rate to determine the total mass of emissions, after correcting for the reduction in exhaust gas mass due to precipitation of the moisture of combustion. This procedure eliminates the need for the Constant Volume Sample (CVS) System attached to the vehicle exhaust while undergoing simulated drive testing on a chassis dynamometer to evaluate compliance of the test vehicle with the Australian Design Rules, ADR27 and ADR37. Sources of error with the procedure are examined by comparing the fuel consumption measured using a volumetric technique during the test with that evaluated by a carbon balance procedure as given in the Australian Design Rules.

An all-ceramic swirl chamber has been developed and analyses and evaluations concerning the strength of silicon nitride ceramic (Si3N4) have been performed with a view to using it for the entire internal wall surface of the swirl chamber. The strength characteristics of Si3N4 and their effect and variation have been determined. On the basis of measurements and analyses of thermal stresses, assembling stresses, etc., investigation of the most suitable construction and assembling methods to reduce load stresses on ceramic, and various kinds of duration tests, the swirl chamber has been confirmed to have the required durability. This engine was found to comply with the 1987 U.S. diesel particulate regulation.

The sequential fuel injection, in which fuel is injected into swirl being generated for mixture stratification, was used to pursue the potential of a lean burn engine for its performance improvement. As a result, it has been found that the most effective method to increase thermal efficiency while reducing NOx emission level is to combine a high-compression compact combustion chamber located on exhaust valve side in cylinder head with DICS (Dual induction Control System). This method was used to build a high-compression lean burn concept vehicle, which was evaluated for compliance to various emission standards. Testing showed that the concept vehicle can improve fuel economy by 10.5% on the Japanese 10-mode cycle, by 8.3% on the ECE mode cycle, and by 6.3% on the U.S. EPA test mode cycle while meeting respective emission standards.

For the purpose of satisfying today's market demands, new 8 and 11 liter diesel engines, named "STORM" series, have been developed and moved into production in 1986. Based on the predecessors which have been produced since 1975, the development of the STORM series aimed high performance, low emission, long life-time and low operating costs. In order to consult customers' convenience, exchangeability of engine parts and commonality of vehicle installations with the former engines had to be maintained. This paper describes the development work of STORM engines, and the design aspects and performance characteristics of these engines.

CORRELATION OF BENDING STRENGTH AND ERRORS OF HELICAL GEAR has not been clarified sufficiently even now. As the investigation by using only experimental method is not sufficient and so the analytical method of obtaining gear bending strength has been developed by one of the authors. Hence, the correlation of bending strength and errors, especially in the aspect of the direction of pressure angle error and tooth trace error, is clarified by this analytical method which was verified by some experiments. And by further investigations, it is confirmed that the helical gear is tougher against the negative pressure angle error, and the fine module gear is sensitive against the errors.

In this paper a computer simulation study on the effects of steering parameters on lateral dynamics of the guideway bus to contribute to a development practice of designing optimum steering control system are dealt with. A stability limit of vehicle lateral motion is analyzed and an emphasis is laid on the effects of moment of inertia of a conventional steering wheel and lateral elasticity of the guide rail which have proven to reduce the critical vehicle speed. It is pointed out conclusively that a normal bus equipped with additional simple guidance equipments can be guided smoothly on a simple guideway at adequately high vehicle speed.

The influence of the tyre properties on the driving behaviour of single-track vehicles has been measured by performing running tests with full-scale vehicles. The indoor dynamic tyre measurements using the sideslip angle as the input signal reveale that the sideforce and self-aligning moment characteristics are helpful explaining the measured driving behaviour. The obtained tyre parameters values and second order equations have been implemented in the simulation program ADINA-MOBSIP. This program is specially conceived for the simulation of the driving behaviour of single-track vehicles and is based on the finite element method.